Jump to content

Recommended Posts

Got 10 Diy install sets for the internal HDMI mod for sale right now.

Keep in mind you should be handy with a soldering iron. It's not a lot more complicated than a chip install but if you already have trouble with an xbox chip leave this mod alone for now.

Price for each set is: 70€ +shipping costs.

Drop me a PM if you want one!

The install set does include the main HDMI mod and the install adapters for ONE motherboard revisions so you have to decide which revision mothebroard to use when ordering

IMG_1776.jpg.51ddad26626a4deda6d09cb2611ea618.jpg

 

Edited by N64 freak
  • Like 5
Link to post
Share on other sites
  • 2 months later...
  • 2 weeks later...
  • 4 weeks later...
  • 2 weeks later...
  • 2 weeks later...
5 hours ago, sosafire said:

hello,

I wish I had some information, is it that your mod hdmi can have a picture in 1080p? Can we add scanlines and so adjust them, as on mod hdmi citrus 3000? Or other settings that we do not see in the video?

Thanks Patrick

I don't think so.  This mod outputs the resolutions that the Xbox is capable of 480p, 720p or 1080i. There is no upscaling or scanline capability added.

  • Like 1
Link to post
Share on other sites

Does this tap into the digital video from the xbox, or is it a component to hdmi adapter?  Ether way im probably gonna end up getting one of these if you still have some this time next month. Looks to be the only easy thing to get digital audio over hdmi. So its the perfect thing for my setup, once i save up and can afford it.

Link to post
Share on other sites
43 minutes ago, 10gignick said:

Does this tap into the digital video from the xbox, or is it a component to hdmi adapter?  Ether way im probably gonna end up getting one of these if you still have some this time next month. Looks to be the only easy thing to get digital audio over hdmi. So its the perfect thing for my setup, once i save up and can afford it.

This takes the component signal and converts it to a digital one.  It's the hardest HDMI mod to do but it is the best HDMI solution out there, in my opinion. 

Link to post
Share on other sites
5 hours ago, TEK Nemesis said:

This takes the component signal and converts it to a digital one.  It's the hardest HDMI mod to do but it is the best HDMI solution out there, in my opinio

Good enough. I don't need the digital video since it(video on the Xbox) doesn't seem to degrade as the capacitors age like the audio does.

Link to post
Share on other sites
  • 2 weeks later...
  • 1 month later...
  • 4 weeks later...
On 7/3/2019 at 3:14 AM, JacobK19 said:

Hello, 

Does anyone know if Chimp will properly display with this mod? I have read that the Chimp program requires a composite output, and will not even work with component. Does this same issue apply with the internal HDMI? Thanks!

I tried Chimp on a version 1.1 with 1 of N64's HDMI mods and No it seems to not work.

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Content

    • By Haizum74
      Are there any issues/conflicts I need to be aware of when tsoping my xbox? Ive been running a soft mod for a week or so and have a sata 500gb HDD locked with apps, games and of course a dash, XBMC4gamers.

      If so I can always put the original HDD in to tsop it that way but then am I good to go with putting the 500gb back and just straight booting? OR, do I need to reinstall everything?


      Any specific bios reccomendations? I will be using the drive as well as the HDD and on 1.4 I think. Certainly not 1.6
    • By Thakarra
      Hey guys, happy new year!
      A few months ago I was given an original Crystal Xbox. As someone who has always been on the Sony side of consoles, I admit, I don't know much about Xbox. However I was told that the Xbox was running EvoX (Can be confirmed, when I turn the Xbox on, there is an EvoX icon on the left hand side of the boot screen) and that the Xbox had a modchip inside.
      The Xbox has been sitting under my bed for a while and I thought today I would dust it out and upgrade the internal HDD. The IDE hard drive inside the Xbox was only 80GB and I had a spare 250GB IDE hard drive I wasn't using. --
      So I went ahead and followed this tutorial: 
       
      Basically I downloaded Hexen 2018 > burned the image to a DVD > put the DVD inside my Xbox > replaced the old IDE HDD with the 250GB one > booted into Hexen 2018 > went into Disk Upgrades > From there I followed the process. 
      After the files had copied over from the DVD, XBPartitioner 1.3 booted up and I made sure that I set the F drive to the full 250GB.
      From there the process was complete. I took the Hexen 2018 DVD out of my Xbox and the UnleashX dashboard popped up. BUT when I look at the drive details on the upper left corner. I can see that there is only around 120gb free on (F:).
      Whenever I try to boot XBPartitioner from the dashboard menu, I get the following error:
      "LBA48 info not found! Custom Partitions will not work with this BIOS! Update your BIOS to one which supports at least LBA48 version 2."
      I done a bit of research and it LOOKS like I need to update my BIOS. But honestly as someone who has no clue what they're doing, this frightens the hell out of me. So that leads me to this post... I'm looking for some help which can preferably be explained in as simple detail as possible, I literally need someone to spoon feed me the steps. I would be so grateful and appreciate it!
      EXTRA INFORMATION - If I load into the EvolutionX dashboard I can see the follow details, which might be relevant.
      BIOS: EvoX M8 (1.6) Kernal: 1.00.5838.01 EvolutionX V+3935
    • By Karl_M
      Hi, I’m new to anything to do with mod chips on the original Xbox so my apologies if I sound like a complete noobie. 
      I recently purchased a Xbox of Facebook market place that has a DuoX2 (blue) mod chip installed. When the console boots is has like a green logo in the top left and Slayers 2.7 underneath the Xbox logo at the bottom of the screen (I’ll add a photo to explain what I’m talking about). Then it boots into evolutionX dashboard I believe. 
       
      I’ve dabbled with soft modded Xboxes before and wanted to take a crack at a mod chipped one but I’m worried I’ll brick the console if I just try and re flash bios and install a new dashboard. So long story short, is it possible to update the bios on the mod chip to someone a little more recent like EvoX M8 or something? The Xbox is 1.4 console. I opened it and cleaned the console of dust and re did the thermal paste and fixed the DVD belt prior to wanting to update the dashboard and mod chips Bios.
       
      any help is much appreciated.
       
      Kind Regards, Karl 



Board Life Status


Board startup date: April 23, 2017 12:45:48
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.