Jump to content

Recommended Posts

19 hours ago, SS_Dave said:

Thanks found them! 👍
https://www.thingiverse.com/thing:3864107 

Would the heat be an issue for the plastic? PLA plastic it starts Melting about 160 F.  

 

Quote

Or you could 3D print some brackets to hold a new fan

1759510231_XboxGPUan.PNG.92a05807936eacb07c649c22d3a56447.PNG

 

Cheers

SS Dave


Soft modding is like masturbating, It gets the job done but it's nothing like the real thing.

 

Edited by FerociousOG
Link to post
Share on other sites
  • 4 weeks later...
On 9/17/2020 at 6:36 AM, SS_Dave said:

Or you could 3D print some brackets to hold a new fan

1759510231_XboxGPUan.PNG.92a05807936eacb07c649c22d3a56447.PNG

 

Cheers

SS Dave


Soft modding is like masturbating, It gets the job done but it's nothing like the real thing.

Is this a 3pin fan? if so does it connect without any modification?

 

Also whats the general thought on spraying WD40 in the fan? like in this vid:

 

I tried taking the fan apart to clean and spray the ball bearings, I looked under the stickers top and bottom but its just solid plastic and no washer 🤷‍♂️

Edited by corona2222
  • Like 1
Link to post
Share on other sites

For real, don't bother lubing the fan becaus it will not hold for long if there is any chance to lub the fan at all. A new fan like the noiseblocker xs2 is 5-6 euros/bucks and hold much longer as a new lubed fan. Noctuas are nice but not for the job in a 1.0. With the little noctua you get worse temps as with a GPU block from a 1.1 and up because the spin to slow and move only half the air as the original fan. The noiseblocker xs2 isn any louder but moves more air and makes is the better way choice without dealing with lubing. Not to mention that this fan also moves way less air as the original one.

Link to post
Share on other sites
  • 2 weeks later...
On 10/16/2020 at 10:28 AM, sweetdarkdestiny said:

For real, don't bother lubing the fan becaus it will not hold for long if there is any chance to lub the fan at all. A new fan like the noiseblocker xs2 is 5-6 euros/bucks and hold much longer as a new lubed fan. Noctuas are nice but not for the job in a 1.0. With the little noctua you get worse temps as with a GPU block from a 1.1 and up because the spin to slow and move only half the air as the original fan. The noiseblocker xs2 isn any louder but moves more air and makes is the better way choice without dealing with lubing. Not to mention that this fan also moves way less air as the original one.

what kind of fan is that? and does it really move more air than a stock xbox fan?

Link to post
Share on other sites
4 minutes ago, bulkchart32 said:

what kind of fan is that? and does it really move more air than a stock xbox fan?

https://www.amazon.com/-/de/dp/B0083A0BY4/ref=sr_1_1?__mk_de_DE=%C3%85M%C3%85%C5%BD%C3%95%C3%91&dchild=1&keywords=noiseblocker+fan+xm-2+-+40+mm&qid=1603621370&sr=8-1

And it dosn't move more air as the stock fan.  The Noctua moves less than half of the stock and the Noiseblocker moves a little more as the half (close to 2/3) of the stock fan. If you want something equal to the stock dan look for the Adda AD0412MX-G70-LF. Which is basicly the same fan just in a normal "fan layout".

And i see i have wrote XS (50mm which is nice for the CPU (see pic above))  instead of XM (40mm fan which is for the GPU). So sry for that.

 

  • Like 1
Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Content

    • By madmon
      Hey so I have a 1.0 and the main fan header isn't working. Can I just replace the mosfet or is there a greater issue? 
    • By tjd2
      So i have got an xbox revision 1.0 for parts. Inside the motherboard was pretty much immaculate with non-leaked clock cap. Sadly the xbox just FRAGged. I did lots of troubleshooting including dumping the eeprom with raspberry pi, testing it with different psu or trying the TSOP bank split trick for coma console.
      I thought, that the TSOP must be faulty so i ordered aladdin xt. However the holes on 1.0 are filled with solder and hard to clean up. In the end, i soldered each leg of the pinheader individually. It looks ugly, but there are at least pretty wet solder joints and modchips do fit in it. Sadly it still frags.
      Images:


      I have:
      1. Grounded the bottom d0 point
      2. Grounded BT on the aladdin
      3. Tested the aladdin in my 1.6 and then reflashing it with indbios
      4.  Replaced a R7D4 resistor i accidentally desoldered
      I also remember, there was possibly a short at Q7R1 part. I fixed it, but two pins next to each other are still shorted according to multimeter. The two pins are those closest to the Q in the Q7R1 marking (left down side on the bottom side picture)
    • By nin1
      Hi, three capacitors that goes to the processor are bulging badly... red things on top etc.. 
      Which caps are best to use? Which uF and volt for them?

Board Life Status


Board startup date: April 23, 2017 12:45:48
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.