GoTeamScotch Posted February 8, 2020 Report Share Posted February 8, 2020 (edited) I'm wanting to use other controllers on my OG Xbox. Controllers such as Xbox 360 and ideally Xbox One controllers. Everyone seems to recommend ogx360, but that seems to require a custom PCB and I'm not sure where to buy it. Alternatively, there's ripdajacker's project, which seems to be less polished but it also appears to support more controllers and only requires a raspberry pi and an atmega32u4 board, which are off-the-shelf parts. What are the differences between these two projects? Which is best? Thanks Edited February 8, 2020 by GoTeamScotch Quote Link to comment Share on other sites More sharing options...
coptimus Posted February 10, 2020 Report Share Posted February 10, 2020 I use a ogx360 and it works like a champ. I bought mine from Tim Kirkup (Tek Nemesis). He does quality work. 1 Quote Link to comment Share on other sites More sharing options...
TEK Nemesis Posted February 11, 2020 Report Share Posted February 11, 2020 OGX360 all the way!!! Quote Link to comment Share on other sites More sharing options...
SS_Dave Posted February 11, 2020 Report Share Posted February 11, 2020 I vote for the OGX360 as well. Cheers SS Dave Those that can Hard-Mod. Those that can't Soft-Mod. 1 Quote Link to comment Share on other sites More sharing options...
GoTeamScotch Posted February 17, 2020 Author Report Share Posted February 17, 2020 Just chiming back in here to say that I tried ripdajacker's method and holy crap. It turned out to be way more complicated than I thought. I've tinkered with Raspberry Pi's and such before, but I wasn't prepare for the learning curve of getting the arduino board flashed and working. I was going mad trying to follow guides and getting it flashed, then it turned out that I had to put it into a certain mode and flash the device within like 2 seconds before it went back to normal mode and I only found that out after like an hour of trying and failing. Anyways, Once I got through setting up the Pi and the arduino board, the wiring diagram didn't match up to the arduino I had (doesn't seem to have an "ss" pin?) so I pretty much giving up at this point. I'm sure someone who's super familiar with all this can figure it out, but I'm tapping out. Anyways, who's got a source for where I can buy an ogx360? Preferably in the US. Quote Link to comment Share on other sites More sharing options...
KaosEngineer Posted February 17, 2020 Report Share Posted February 17, 2020 In the US - https://www.chimericsystems.com/product/ogx360-board However, they are currently sold out. Fill out their contact form to see when more will be available. Quote Link to comment Share on other sites More sharing options...
Kekule Posted February 17, 2020 Report Share Posted February 17, 2020 53 minutes ago, KaosEngineer said: In the US - https://www.chimericsystems.com/product/ogx360-board However, they are currently sold out. Fill out their contact form to see when more will be available. Yeah, China still isnt fully recovered from the corona virus shutdown, but I'm starting to get the parts now. Quote Link to comment Share on other sites More sharing options...
KaosEngineer Posted February 17, 2020 Report Share Posted February 17, 2020 12 hours ago, GoTeamScotch said: Just chiming back in here to say that I tried ripdajacker's method and holy crap. It turned out to be way more complicated than I thought. I've tinkered with Raspberry Pi's and such before, but I wasn't prepare for the learning curve of getting the arduino board flashed and working. I was going mad trying to follow guides and getting it flashed, then it turned out that I had to put it into a certain mode and flash the device within like 2 seconds before it went back to normal mode and I only found that out after like an hour of trying and failing. Anyways, Once I got through setting up the Pi and the arduino board, the wiring diagram didn't match up to the arduino I had (doesn't seem to have an "ss" pin?) so I pretty much giving up at this point. I'm sure someone who's super familiar with all this can figure it out, but I'm tapping out. Anyways, who's got a source for where I can buy an ogx360? Preferably in the US. Which Arduino board are you using? There are many different models. Quote Link to comment Share on other sites More sharing options...
GoTeamScotch Posted February 17, 2020 Author Report Share Posted February 17, 2020 OSOYOO Pro Micro ATmega32U4 5V/16MHz Module Board with 2 Row pin Header for arduino Leonardo Replace ATmega328 Pro Mini Ripdajacker's requirements list "Arduino Pro Micro or equivalent (atmega32u4 based)" so I'm pretty sure this is a correct board to use. Where I'm getting hung up is the wiring of the two boards together. I can see that the Arduino is wired to the Pi's GPIO #9, #10, and #11 pins (MISO, MOSI, and SCLK), but I'm unsure about the brown wire going from the Arduino to the Pi. Ripdajacker's diagram https://github.com/ripdajacker/xpad-avr/blob/master/xpad-avr-wiring.pdf Arduino pinout: https://osoyoo.com/wp-content/uploads/2018/06/Capture_115.png Pi GPIO pinout: https://i.imgur.com/IINr0h3.png I'm pretty sure I can just match up the wiring diagram, but last I looked at it I couldn't match the pinouts and I didn't want to burn the board by trying and failing. Plus, I've been looking into the ogx360 more lately and it looks to be a lot more polished in general, which has me curious. And $67 isn't a bad price for getting a full working kit. Quote Link to comment Share on other sites More sharing options...
Subieroadkill Posted March 18, 2020 Report Share Posted March 18, 2020 (edited) I have been waiting to order one of these ogx360s so bad for a couple months now.......I got the card locked and loaded but I can never find anyone who has a complete kit. Edited March 18, 2020 by Subieroadkill Quote Link to comment Share on other sites More sharing options...
SS_Dave Posted March 18, 2020 Report Share Posted March 18, 2020 Hi Subieroadkill N64 freak has a really compact 2 port version but he is waiting on parts to make some more so probably approx 5 weeks delay maybe send a PM to him and get on the waiting list . His version is plug and play just add a MS 360 wireless receiver for the Xbox 360 controllers or a 8bitdo receiver for a Xbox one controller and your off and playing. Cheers SS Dave Soft modding is like masturbating, It get's the job done but it's nothing like the real thing. Quote Link to comment Share on other sites More sharing options...
TEK Nemesis Posted March 20, 2020 Report Share Posted March 20, 2020 On 3/18/2020 at 12:42 AM, Subieroadkill said: I have been waiting to order one of these ogx360s so bad for a couple months now.......I got the card locked and loaded but I can never find anyone who has a complete kit. I have hundreds in stock and can ship ASAP. The easiest way to reach me is on Facebook (The Mod Shop by TEK Nemesis). PM here if you don't have access to Facebook. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.