Jump to content

Search the Community

Showing results for tags 'clock'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Off Topic
    • New Member Introductions
    • Rumble Pit
    • Suggestion Box.
  • General Xbox Discussion
    • General Xbox Discussion
  • Original Xbox Modding Forum
    • Hardware Mods
    • Modchips
    • TSOP Flashing
    • Softmods
    • Repair
  • Xbox Case Modding
    • Case Mods
    • Lighting & Electrical Mods
  • Tutorials
    • Official Tutorials
    • Tutorial Submission
  • Software
    • Bios
    • Dashboards
    • Installation Disks
    • Applications
    • Games
    • Emulators
    • Homebrew
  • Xbox Collecting
    • Xbox Collection Showcase
  • Rare and Uncommon
    • Rare and Uncommon Xbox Hardware
    • Rare and Uncommon Xbox Software
  • Vendors
    • N64 Freak's Products
    • Barnito's Products
  • Development
    • Rocky5's Projects
  • Online Play
    • Game Night
  • Classifieds
    • Wanted
    • For Sale
  • Moderator Section
    • Moderator Back Room

Product Groups

  • Vendor Forum
  • Membership Subscriptions
  • Forum Ads

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


About Me

Found 10 results

  1. Time passes by, so does the life of our OG Xbox Clock caps (if they are not removed already) but also technology in cap replacement options. So I wonder what the most Reasonable/ Convenient/ Easieast/ Safest/ Cost efficient/ Clock cap replacement of today could be? I know some people are not bothered without it and some people (lile myself) that would like to have it working Through the years I read that it can be everything inbetween replacing it with a 1F 2.5v original spec AeroGel cap, 10F 2.5v AeroGel for longer working time, a CR2032 battery socket with 1N4148 diod in series to prevent REcharge, which would not be good, 2.4v NiMh rechargable battery. My idea, not yet installed and tested, is to solder an AAA batteries socket with two 1.2v 800mA replaceable batteries to the old Clock Cap points and try to fit it in somewhere. The batteries gives 2.7v fully charged and would (theoretically, if the Xbox can give them enough charging) give more than enough unplugged power time and it would all in all cost around 5$. So now in 2020, what is your clock cap replacement (ideas, pictures, pros/cons, results)?
  2. I finally got around to removing the clock cap v1.2 board, though i would completely strip it down as it was half way in bits anyway, and give it a good clean out. Washed the plastics etc cleaned motherboard, fan, heatsink (Still need to apply new thermal paste) popped her back together after the plastics had dried and to my amasement it works. The cap was fine to be honest, no sign of any problems at all. I was quite supprised how clean it was to be honest, just a light bit of dust on the motherboard. Thanks allf or looking.
  3. I recently took my old xecuter 2 modded 1.4 xbox out of storage and have replaced the drive and removed the clock cap and its working great. The only issue is if i power off for a few mins and then power on I get a blank screen and it wont boot. If i disable the mod chip and go into the normal OS its looking to set the time(fair enough as i removed the cap). Once i set the time and enable the mod chip it boots fine. Is there a way to hard set the time so this doesn't always happen. My UnleashX front end gets the time from the internet correctly anyway. Any help or guidance appreciated guys.
  4. Are here any repercussions to that? i did it to prevent leaking but i'd like to know if it needs replacing for some feature or if it was unnecesary.
  5. I installed Rocky5's Xbox Softmodding Tool v1.1.6 on both my v.12 and v1.6. The clock is set to autoset the time /date but it seems to be getting the wrong timezone, and I can't find where to change it. Could it be it needs a different SMTP IP address? I'm on GMT +0 (Lisbon, London).
  6. Hi all, I have recently got into the modding scene and after some successful Wii mods have decided to turn my hand at the OG Xbox. I had one of these when I was a kid with a chip on it (don't know to much info as was a kid). I recently picked up 2nd hand Crystal OG Xbox's. One of them already has been softmodded and the other is a virgin, never had the lid popped. I am aware that the clock capacitor needs removing off of all motherboards rev. 1.1-.1.5 however, I have read places that you can cause the system to boot loop if not done correctly. My question is, I have a virgin, a softmod and a chip. Which of these is is safe to remove the capacitor from without getting into a bootloop? I am also finding the most up to date software and guides/information hard to find as there is information floating around from over 10years ago so hoping someone can push me in the right direction with dashboards and other ""basic info" on the latests and most supported software that would be a god send. Many thanks
  7. I’m new to the modding scene, and I’m not an electronics wizard or software genius. I have a 1.1 and I keep seeing that I should absolutely move the clock capacitor. I have looked into why, and I guess it has a tendency to leak all over the MB? Can somebody clarify this for me? (This is the best spot I thought to post this due to motherboard alteration)
  8. It has been some years since our beloved xBox was released and some parts have begun to decay. It is commonly advised to remove your clock capacitor and replace any leaking. 1st step, clear any leakage. It's acidic afterall and you'll need a tight grip. 2nd Gently pull at the capacitor being removed while applying heat to the solder with your iron. 3rd Once removed, prepare your replacement capacitor. The longer pin is usually positive. Align these with the holes your old capacitor was soldered into. If you are unable to push it through, apply heat to melt any solder blocking the hole. 4th once pulled through, bend each pin iutward to hold the capacitor position. You don't want it falling out or becoming loose. Apply solder at the base of each pin. 5th trim pins just above the solder. I used nail clippers as they were able to achieve a shorter trim. That and i misplaced my wire cutters. Refit your motherboard etc Power up and pray
  9. I was bored this evening so I pulled out an Xbox and TSOP'd it with iND-BIOS and installed a new old-stock 500GB IDE Maxtor hard drive. The clock capacitor has been removed, the DVD drive (Samsung) has a new drive belt installed and the case has been cleaned and polished-up, looks great. Currently transferring over XBMC4Gamers as the primary dash and all emulators are outfitted with the ResurrectionXtras video and box art/screen shot packs-- speaking of emulators, this includes the latest build of EWJ's curated Surreal64 romset, and almost every game runs great. The controller is in great condition as well, disassembled and shell cleaned. Asking $90+shipping if anyone is interested. Thanks!
  10. I'm new to the xbox modding scene. I was given a v.14 og xbox from a friend that was never modded/tampered with. I'm thinking about doing a tsop since I like the idea of not having to deal with locking/unlocking hard drives. My question is, if I remove the clock capacitor, which bios make sure I don't run into a clock boot loop error 16?

Board Life Status


Board startup date: April 23, 2017 12:45:48
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.