Search the Community
Showing results for tags '360'.
Found 18 results
-
Just picked up 3 defective Xbox 360s for $5. Hoping the RF boards will be good to connect 360 controllers to the og
-
Hi all, Long time modder and lurker, first time poster but I wanted to share a project I have been working on the last couple months. It is a small PCB which allows you to use Wireless Xbox 360 controllers (via the Xbox 360 USB Wireless Receiver) on an OG Xbox console. The design is loosely based on another similar project I did for the Nintendo 64 console https://imgur.com/gallery/HVLea3d Following the release of this board another forum user sent me an email asking if this device could be adapted for the OG Xbox, and funnily enough that was the next thing I was going to attempt! I wanted to support the following features atleast: Up to four players with rumble support. 100% USB Bus Powered so no external power supply needed. Fast bootup time, so it's up and running in time for the OG Xbox. Low input lag. As always, this is a hard thing to measure, however I can say that an OG Xbox controller is polled by the console every 4ms or so. My software gathers all the Xbox 360 wireless controller data, collates it and generates all the HID reports every 4 ms aswell. It's possible an input may miss this 4ms window, so would happen in the next 4ms window. As you probably know, an OG Xbox controller is basically a USB HID device, however it has some custom requests and other slight differences, meaning that it doesn't work on a Windows machine without a custom driver, and conversely a generic HID controller will not work in an OG Xbox so there was some work in getting a reliable and compatible solution working. To support four controllers, it is necessary to have 4x Full USB device controllers. However I imagine most people would rarely play with 4 people at once so my design is modular meaning you can support anywhere from one up to 4 players as required to keep cost down. This is a link to the github repo with what I came up with https://github.com/Ryzee119/ogx360 A link to my etsy store where you can buy one pre-assembled https://www.etsy.com/au/listing/672315615/ogx360-add-wireless-xbox-360-controller Cheers!
- 310 replies
-
- 14
-
-
-
- xbox 360
- wireless controllers
- (and 7 more)
-
Simply one of my skins for UnleashX. xboe_1_2019_F.rar
-
So I've figured out how to get games downloaded on a 360 to work on a real Xbox. You might be interested in this if you get the Games With Gold titles, since they've had some pretty good ones in the past like Mercenaries and some of the Star Wars games, and Destroy All Humans is available right now. Do note that since we're dealing with Xbox 360 Marketplace here, the only real way to get these onto your console is through buying and downloading them, so Piracy really isn't a thing here. To begin, you will need two Xbox 360 tools: GOD2ISO and velocity-master. You'll also need a USB drive big enough to hold your game. You'll also have to enable the "show hidden files" setting in Windows Explorer. Start by copying the game to your USB drive from the Dashboard. Plug the drive into your PC. Go to Content > 0000000000000000 and you will see several folders. I've attached a picture of Halo 1's folder layout. Open that extensionless file in GOD2ISO and save a place to save your ISO file. Then use Velocity to extract your ISO to a new folder. From there, you should be able to FTP the folder over to your Xbox and play the game. -
i know the drive from a 360 will not work with an og xbox but are there any parts from a 360 drive that would work? for example, would certain lasers like the SOH-DX1 from a 360 drive work in an og xbox drive that has the same model laser?
-
Hi, bought the XBox 360 along time ago, not just for me but for my 2 new kids ... both boys. It was supplanted by a wonderful and powerful PC. But, now it is back on and the games still seem great. So, I have a new found desire to get the most out of this console. Glad I found this forum and hoping to learn from you all. Will contribute where I can. To start though - one of our discs is playing up and I just wondered what is the best approach apart from trying to polish the scratches out of the surface.??? My initial thoughts are to install a program to copy the disk to hdd. This should make it a little faster to load and more reliable for normal use. I see a progam called dvd2xbox was available but don't know if this is the best and only choice. Any advice will appreciated. Thanks to those who made this forum available and all members... Brett
-
Hey Guys! Is there a way to Copy my save game files from my modded Xbox to my 360 with RGH (for backwards compatibilty) if yes: how can I do that? :)
-
Hi guys, newbie to the forum. I've just ordered an Xbox One X and am now looking at a few games to go with it. Keen to buy Skyrim and Forza Horzon 3 (interesting contrast I know). The local game store has a deal for 4 Xbox 360 games for $20. Skyrim and Forza Horizon 3 are included in the deal, while their Xbox One counterparts are triple the price. So my question is, is it worth paying extra for the Xbox One version vs the 360 versions considering they are both "Xbox X enhanced"? Hope that makes any sense. Thanks to anyone with any advice &/or knowledge on the subject. Cheers -
Here's a custom mod I did back in 2008 of an Xbox converted over to a Xbox 360 case. I was running UnleashX using an 360 skin. It's funny looking at my old photos and seeing what things I did. Lots of improvising. Notice the rear of the case? haha
- 12 replies
-
- 2
-
-
- xbox-scene
- xbox to 360
- (and 5 more)
-
Ever wanted to add a new D-pad to your controller? Probably not. But im still gonna show you how. Both methods are on an S-Controller. I haven't tested on a Duke or any other controller. If you wanna try then let me know how it goes. Tools/Materials You'll need for this mod Phillips Head screw driver mini Phillips head screw driver Regular D-pad from an xbox 360 Controller or A Transforming D-pad from a 360 Controller (Depending on which mod you wanna do) Needle Nose pliers or Wire cutters(For method 1) Dremel/Rotory tool Sanding Barrel and cutting disc for your Dremel. and 10-15 minutes of your time. PART A: Disassembly First you'll need to pull apart your controller. there are 7 Phillips head screws on the bottom, 1 is under the barcode sticker in the center. once removed you can pull the bottom part up and remove the internals. Once you have everything stripped from the top half of your shell you'll need your Mini Phillips head screw driver. remove the 2 screws holding your original d-pad in place and pop it out. Part B: Mod Method 1 Now take your new 360 d-pad and look at it . the one on the left is the original S D-pad. right is from the 360. You'll want to remove the locating tab on the right side using your cutting disc. Alternatively you can snap it off with a pair of needle nose pliers or even some wire cutters. Now pop it in and reassemble everything. Your done!! This mod isnt really for the Original colored D-pads (Grey or Black) But once done you can buy many different colored ones for the 360 controller. Great if you plan on painting your controller. Part C: Mod Method 2 First you'll need to pull apart your controller (Refer to Part A) Once taken apart you'll need to take your Dremel with the sanding barrel and remove the internal part of the d-pad mounting location. Go slow and take your time. Don't cut any deeper than whats in the picture. If you cut too deep you will ruin the controller. all you wanna do is cut/sand it down smooth to the cylinder wall.(If that makes sense) Now you'll need to flip your controller over, and put the new D-pad into place. You'll notice the locating pins are preventing it from going in. You'll want to take your cutting disc and cut notches in the Controller so the D-pad can go in. (I cut to vertical slices and then used my screw driver to snap the piece off) Not the cleanest way to do it, but it works. Once the notches are cut you should be able to put everything back together (Using the original Rubber insert for the d-pad) and you are done!! Enjoy your new Transforming D-Pad!
- 7 replies
-
- 2
-
-
-
- d-pad
- transforming
- (and 10 more)
-
Hello, I recently decided to mess with my recently purchase Xbox 360 development kit and i am having some trouble. I would like to get it set up to Xbox neighborhood and play debug games on it but Xbox neighborhood cant seem to find my system. If possible, could some one walk me through how to set up Xbox neighborhood, how to use it, and finally how to load debug games to it. just to clarify, my system is not a JTAG or RGH, it is an official dev kit so i dont know if the process between the two is much different. Any help will be greatly appreciated. Thanks Aidan -
I just got a 360 and am hoping to get my original Xbox games working. Thus far, only Halo will play. I tried Deathrow, Quantum Redshift, and Black Stone, but they won't run. I did think they were on the compatible list. This is a used console, so I don't know if maybe I am missing an update of some kind.
-
So yes, guys that is my question, please help me here. I am trying to buy an original component xbox 360 cable, to then build an Xbox component cable (using a tutorial from the forum). I live in south america and buying internationally is not an option (2 to 3 months of wait). Could this be an original 360 component cable? Don't laugh if is not, it looks kinda of in bad shape, but it has a similarity to my composite cables for the OG Xbox. It the ONLY one I have found in my entire country (seller SAYS it's original): -
Will a 360 usb controller work on a OG Xbox? I see that the OG Xbox has a 5th wire labeled timing signals.
-
not ogxbox related but surely there is a few rgh modders in the group decided to share my gerber for the community to order and enjoy b9bbcde2263011e999d9026a86b9cae7.zip
-
I have been thinking about doing a mod to allow for the use of a Xbox 360 controller. I used to have a wireless S-controller rip off which worked great but I lost it during moving some time go. I also have the Logitech one, but I really despise it. It just feels wrong and in no way is as good as the s-controller. I do love the 360 controller and use that for my 360 and my Opensuse based media centre. So I would also like to use it on a Xbox. I was thinking of using a Raspberry Pi, a Xbox 360 usb receiver, custom usb connector/output to connect to the Xbox motherboard and connector for auto on/off with the xbox button on the 360. On the Pi I want to load a lightweight Linux with the Xboxdrv driver to take the input of the 360 controllers and translate it to the OG xbox controller output, using some of the code from this same driver which also supports the original xbox controller. A bit worried about lag and my ability to mod the driver code, but seems like an interesting challenge. Any one seeing other challenges or maybe has tried this and found it impossible
-
Wondering if perhaps my DIY 360 component cable tutorial should be moved to the official tutorial section as it has more views than all of the official tutorials combined. I posted it in the hardware mods section originally.
-
Hi I know this site is for original xbox but if anyone is looking for a all in one download pack of jrunner I have a copy right here https://drive.google.com/open?id=14AfY7aw35d-mitvLDtAIbWlIMbTNE0Ne
Board Life Status
Board startup date: April 23, 2017 12:45:48