Jump to content
OGXbox.com

prtscn

Members
 View Profile  See their activity

  • Posts

    464

  • Joined

  • Last visited

  • Days Won

    6

 Content Type 

Everything posted by prtscn

  1. prtscn
    you can set manual fan speed. Test all speeds to try replica that whining sound.
  2. prtscn

    Failed Tsop

    prtscn replied to prtscn's topic in TSOP Flashing

    not the point. I don't understand why it's not booting, i flashed appropriate bios. Tsop worked perfect with previous bios.
  3. prtscn

    Failed Tsop

    prtscn posted a topic in TSOP Flashing

    Console won't turn on, only blink green few times. CD drive won't open, nothing. tried to flash x3 1MB bios to 1.0 motherboard. I had previously flashed 256kB, 512kB. Any directions?
  4. prtscn
    i got it like that. Chip works, changes modes, but there is no bios on board, not even backup.
  5. prtscn
    i have dead xecuter 3 chip and i was thinking to hotswap xenium chip with dead flash xecuter 3 and try to flash it? Possible?
  6. prtscn
    upgrading from 500 to 1TB. But how i would utilize new space without formatting?
  7. prtscn
    I have only 1 sata adapter and want to upgrade to 1TB. I have usb adapter, and i could connect my old 2.5" hdd to my laptop and use hirens CD to clone HDD. I think it would work, it would copy all sectors, but what about formatting?
  8. prtscn
    ps1 (some models) ,ps2, xbox, xbox 360 use same alps analog sticks, so pots from these controllers will work with each other.
  9. prtscn
    softmod and forget discs. there is no POTS to play around.
  10. prtscn
    buy simple electrolytic capacitors, specifications rated to original ones. axial-leaded, radial-leaded, it refers to capacitor legs. Radial leaded is the ones you need.
  11. prtscn
    component would be the way to go. HDMI adapter is just a transcoder from component to HDMI signal, problem is they are not accurate at best. Colour accuracy, input lag, etc. RGB singal range is not known, crushed black or picture is grayish.
  12. prtscn
    you can add rom location from F drive. No need to transfer to other partition.
  13. prtscn
    fu-ge-da-boud-it :D
  14. prtscn
    Nothing, if it goes bad, it goes. Since it's not possible to remove the propeller shaft assembly to service it. You could try buying old VGA gpu with those little fans. I tried to take fan from fx5500, but fan is too big, i bet there exist smaller fans.
  15. prtscn
    You need to have 80pin IDE cable. Don't forget that. Just follow the video. 2TB is max. Also check compatibility if it's lockable.
  16. prtscn
    If you can use component, use component. Transcoding signal is lame, specially with cheaply designed products. And no one knows if it outputs 16-235 or 0-255 color range, which is very important. Salvage AV plug, buy 360 component cable - profit.
  17. prtscn
    desolder https://www.youtube.com/watch?v=UhyTpcBY710
  18. prtscn
    Every solder has its own melting point. But for motherboard 200 is optimal temperature, above is risking lifting pads. Thermal mass, etc, is also a factor.
  19. prtscn
    don't use like 400C of temperature. Melting point of lead free solder is about 180-200. Soldering paste is your best friend. For starters, you have to train. People train by using thick gauge copper wire and apply solder to it. Also faulty motherboards.
  20. prtscn
    do you run it in 4:3 or 16:9 setting?
  21. prtscn
    It is possible. Remove these stupid memory slots first, create cutsom 3D printed bottom part of the controller, have some sort of wireless communication so it could transfer direct USB data to remote receiver, and receiver translate it again to original USB data form. Of course internal battery is needed.
  22. prtscn
    Could be bad cable on adapter itself. faulty cable should not need replug, more likely indicates that it's a adapter's fault. And don't even think about trying to buy third party OG xbox ontroller, they all suck. Maybe logitech don't.
  23. prtscn
    these cables suck. you have to DIY. i think the problem with this cable is splitter at the end, it uses 4 contact two sided board, 5 contacts = 10 soldering points. that bread board only have 8 points and is poorly designed. And i think crosstalk and other magnetic phenomenons happens there, not in the cable itself, since it's twisted pair, braided core.
  24. prtscn
    when you go to downloader you can select to update to test version
  25. prtscn
    Yes, download trainers via downloader menu, and after install you can select trainers in game select screen by pressing context menu button (white), and select trainers. With trainer enable you will see icon to appear, indicating that trainer is enabled. Simple and easy. Test versions of xbmc4gamers is even better, more smooth.

Board Life Status


Board startup date: April 23, 2017 12:45:48
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.

  I accept