Moving From Softmod To Modchip

[archfranck]

 

ok fixed boot dash now xbmc. So now I have the tsop and can I put any hardisk without cloning as for the soft mod? I have this 1 terabite hard disk with 80 pin cable and sata adapter. But it gives me recognition problems now I try again. Anyway with the conductive paste and the small syringe it's really easy.

[SS_Dave]

Now you fit the new hard drive and use you install disk 

Slayer 3.7 is ok or Hexen 2020

 

Cheers

SS Dave

Soft modding is like masturbating, It gets the job done but it's nothing like the real thing.

[archfranck]

i think this hard disk no compatibily.. now try

[SS_Dave]

any error on screen?

 

Cheers

SS Dave

Soft modding is like masturbating, It gets the job done but it's nothing like the real thing.

 

 

[archfranck]

 

It has only one problem I noticed .. that if I open it from the dashboard it turns back on by itself and I have to turn it off from the power button. But then the power does not turn on but from the eject button .. the trolley comes on and then I have to close it again ... I don't know .. but it does nothing

[SS_Dave]

I would have a look at the bottom for damaged tracks like this

 

 

 

Cheers

SS Dave

Soft modding is like masturbating, It gets the job done but it's nothing like the real thing.

[archfranck]

now everything works I put the 80 wires cable and adapter and hardisk and it works both the shutdown and it has also detected the new hardisk ... everything is going well now I format and install dash let's see for the partitions if I have problems

[archfranck]

no I am not understanding anything anymore .. now it does the same ignition problem and I was unable to install the dash after 20-sec sometimes after 2-3 min it turns off everything .. I have to understand if it is a cable adapter problem ide or hardisk

[SS_Dave]

did you have a look at the traces on the bottom..

 

Cheers

SS Dave

Soft modding is like masturbating, It gets the job done but it's nothing like the real thing.

[archfranck]

 

always problems ... check tonight ... ok dave thanks

[archfranck]

hard disk 1 tb is ok i put in other xbox.. cable is ok and sata adaptador is ok..

 

 

I think you're right it seems to me that some tracks are interrupted, but repairing it is impossible for me too small ... and however this could be the problem with the power button. But I have another problem which after 3-4-5-10 min turns itself off.

[Ging3rguy]

Do you have a multimeter, you can check for continuity on the traces?

[SS_Dave]

29 minutes ago, archfranck said:

hard disk 1 tb is ok i put in other xbox.. cable is ok and sata adaptador is ok..

 

 

I think you're right it seems to me that some tracks are interrupted, but repairing it is impossible for me too small ... and however this could be the problem with the power button. But I have another problem which after 3-4-5-10 min turns itself off.

You will need to add some wire links.

 

  

You link the 2 blue spots and the 2 purple spots.

 

 

I would also have a look at this.

 

 

Cheers

SS Dave

Soft modding is like masturbating, It gets the job done but it's nothing like the real thing.

[archfranck]

ok azz eheheh i think my problem is track a-b-c

ok if have time try ...

next week i have 2 xbox 1.6 ...softmod or chipmod??

 

I already know your answer

[SS_Dave]

This is the wire I would use.

 

It is a single strand wire.

 

 

Cheers

SS Dave

Soft modding is like masturbating, It gets the job done but it's nothing like the real thing.

[archfranck]

yes i have..colour yellow but equal...

 

ok come on I dedicate myself to those tracks of the button on off then calmly step to 2 xbox 1.6

[archfranck]

 

the last xbox where I made the tsop with conductive paste is a version 1.4, but in the tutorial I speak of 1.0-1.1 or 1.2-1.3 but not of 1.4 ... it is the same as for the v. 1.2-1.4?

[archfranck]

Dave I had an idea I could use conductive paste, for the tsop it worked, then I noticed that it becomes hard enough so I could place it over the wire and with an adhesive tape hold it 1 hour and it becomes hard it is easier with the syringe I don't risk burning anything with the soldering iron.
Anhe if I put too much and goes on the next track I do not risk because the motherboard and the tracks next to it are isolated .. according to me it is a method to try .. now I do tests on a test circuit and see after how hard it hardens.

[SS_Dave]

The conductive paint would work to hold the wire but I don't think it would be long lasting fix.

I would suggest you practice soldering on a old computer board.

 

 

Cheers

SS Dave

Soft modding is like masturbating, It gets the job done but it's nothing like the real thing.

[archfranck]

 

ok i try and i will let you know the results eheheh

[SS_Dave]

You only need the power and eject links the others are for the LED

And a version 1.2 - 1.4 are the same.

 

Cheers

SS Dave

Soft modding is like masturbating, It gets the job done but it's nothing like the real thing.

 

 

[archfranck]

 

then Dave realized that only tracks A and B were interrupted although I also soldered C. I used the soldering iron on the one hand easier and the other with the paste .. which, however, hardens as soon as it hardens. I reassembled everything and in the meantime the power function button .. for now I have turned on the xbox for 10 minutes and it still hasn't turned off ... maybe I did it ... damn you are fantastic in this forum ... in Italy there are no such experts .. I believe that the British are the best in dealing with the Xbox 1 model

[SS_Dave]

That is good to see you have it working.

 

And I live in Australia..

 

 

Cheers

Dave

[archfranck]

 

 

Australia ahhhhhh i think england hahahaah  .. ok

then the power button worked only the first time now it does not go anymore, and as soon as I turn off the dash it restarts by itself. The positive side for now is that it doesn't turn off, I kept it on for more than 1 hour and it didn't turn off. Maybe for the power button I also have to connect the points C-D-E. Maybe I see how it works in case I connect them even if they gave me continuity, maybe they are breaking.

Edited June 15, 2020 by archfranck

[archfranck]

azz same problem now 30 min and power offf...booooo

if have time connect point C-D-E and stop and other xbox

Edited June 15, 2020 by archfranck