DARK A Posted December 25, 2023 Report Share Posted December 25, 2023 i know you are focused on og xbox but i guessed you have knowledge on 360 modding i have a problem i was trying to start rgh 1.2 my fat falcon xbox 360 but i had a problem im using jr programmer and coolrunner rev c and jrunner with extra i didnt start soldering the coolrunner yet i only solder programmer and i got to read the nand with no error 2 times but after Writing glitch.ecc to Nand i got these errors Error: 000 writing block 17 Error: 000 writing block 21 Error: 000 writing block 40 Error: 000 writing block 4D what im doing wrong ? and if i use the picoflasher i get better results ? ps: i forgot to backup the nand im i done for ? if anyone curios here is my soldering wires Quote Link to comment Share on other sites More sharing options...
Marty Posted December 25, 2023 Report Share Posted December 25, 2023 2 hours ago, DARK A said: ps: i forgot to backup the nand im i done for ? Your NAND dumps should be in a folder in JRunner called "output". Also, that soldering is atrocious. Errors on blocks are almost always wiring/soldering related. RGH is very sensitive to solder connections and wiring. Which guide are you following? Quote Link to comment Share on other sites More sharing options...
DARK A Posted December 25, 2023 Author Report Share Posted December 25, 2023 18 minutes ago, Marty said: Your NAND dumps should be in a folder in JRunner called "output". Also, that soldering is atrocious. Errors on blocks are almost always wiring/soldering related. RGH is very sensitive to solder connections and wiring. Which guide are you following? i forgot to write that i read the nand a secend time after the fail of ecc write so im i done for ? atrocious ... yeah its my first time i did better after on the og xbox Quote Link to comment Share on other sites More sharing options...
Marty Posted December 25, 2023 Report Share Posted December 25, 2023 Your NAND dump should be in the "output" folder. Quote Link to comment Share on other sites More sharing options...
DARK A Posted December 25, 2023 Author Report Share Posted December 25, 2023 21 minutes ago, Marty said: Your NAND dump should be in the "output" folder. so i should get the one i read thie first time because it did say the secend time i read the nand : different nand do you want to overwrite and i choose yes ? Quote Link to comment Share on other sites More sharing options...
Marty Posted December 25, 2023 Report Share Posted December 25, 2023 If you followed MrMario's guide, you should have a functional NAND dump. There's no reason for it to be different if you didn't finish the RGH. 1 Quote Link to comment Share on other sites More sharing options...
DARK A Posted December 25, 2023 Author Report Share Posted December 25, 2023 4 minutes ago, Marty said: If you followed MrMario's guide, you should have a functional NAND dump. There's no reason for it to be different if you didn't finish the RGH. thanks so how to return the nand ? Quote Link to comment Share on other sites More sharing options...
Marty Posted December 25, 2023 Report Share Posted December 25, 2023 Wire the NAND reader back up and re-flash the stock NAND with Jrunner. 1 Quote Link to comment Share on other sites More sharing options...
Bowlsnapper Posted December 25, 2023 Report Share Posted December 25, 2023 13 minutes ago, DARK A said: thanks so how to return the nand ? J runner should do all of this automatically since it's pretty thorough. that soldering needs to be done better so you know it won't be a problem for you. I would use kynar wire for those points. The wire you're using is friggin HUGE. You're making sure to use plenty of flux, right? 1 Quote Link to comment Share on other sites More sharing options...
DARK A Posted December 25, 2023 Author Report Share Posted December 25, 2023 1 hour ago, Bowlsnapper said: J runner should do all of this automatically since it's pretty thorough. that soldering needs to be done better so you know it won't be a problem for you. I would use kynar wire for those points. The wire you're using is friggin HUGE. You're making sure to use plenty of flux, right? im using the wires that came with jr programmer Quote Link to comment Share on other sites More sharing options...
Marty Posted December 25, 2023 Report Share Posted December 25, 2023 3 minutes ago, DARK A said: im using the wires that came with jr programmer Yeah, sometimes the camera makes things look bigger than they are to scale. I've used 28gauge wire too. You should shorten your leads and clean your work though. 1 Quote Link to comment Share on other sites More sharing options...
Bowlsnapper Posted December 25, 2023 Report Share Posted December 25, 2023 3 hours ago, DARK A said: im using the wires that came with jr programmer Not trying to give you a hard time at all. The wires that come with the programmer are honestly bigger than you wanna be dealing with, if you can help it. I used a pi pico and used 30AWG wire. It gives you much more room to work with and isn't individually stranded. Check the zoomed full photo. You'll see what I mean. 1 Quote Link to comment Share on other sites More sharing options...
DARK A Posted December 28, 2023 Author Report Share Posted December 28, 2023 On 12/26/2023 at 2:12 AM, Bowlsnapper said: Not trying to give you a hard time at all. The wires that come with the programmer are honestly bigger than you wanna be dealing with, if you can help it. I used a pi pico and used 30AWG wire. It gives you much more room to work with and isn't individually stranded. Check the zoomed full photo. You'll see what I mean. i figured it it wasnt my soldering it was jr programmer it wasnt working that good i switch to picoflasher and its fully working . so how to retun to stock or working nand now ? because i lost my original nand , my console is falcon or is the console done for ? Quote Link to comment Share on other sites More sharing options...
Bowlsnapper Posted December 28, 2023 Report Share Posted December 28, 2023 1 hour ago, DARK A said: i figured it it wasnt my soldering it was jr programmer it wasnt working that good i switch to picoflasher and its fully working . so how to retun to stock or working nand now ? because i lost my original nand , my console is falcon or is the console done for ? Are you afraid of losing your original flash? Is that what your concern is? ... I wouldn't be As long as your flash is good, of course. What was your output, anyway? Was anything actually succesfully written with jrunner? Are you able to boot right now? If all you had was unsuccessful writes and you can still boot, just run again using the tutorial and jrunner will do everything for you, step by step! https://xbox360hub.com/guides/rgh-3-guide/ 1 Quote Link to comment Share on other sites More sharing options...
DARK A Posted December 28, 2023 Author Report Share Posted December 28, 2023 12 minutes ago, Bowlsnapper said: Are you afraid of losing your original flash? Is that what your concern is? ... I wouldn't be As long as your flash is good, of course. What was your output, anyway? Was anything actually succesfully written with jrunner? Are you able to boot right now? If all you had was unsuccessful writes and you can still boot, just run again using the tutorial and jrunner will do everything for you, step by step! https://xbox360hub.com/guides/rgh-3-guide/ its not the flash its the nand i think its corrupted. my output is i try both hd and av nothing shows up. yes after using picoflasher every time i read and write i got successful with no errors. no i only get middle light blinking and some times 2 red light up right and down left Quote Link to comment Share on other sites More sharing options...
DARK A Posted December 31, 2023 Author Report Share Posted December 31, 2023 (edited) i try diffrent console i got read nand no problem and i creat and write xell no problem i try booting the console with eject to get the key it turn on by flashing the middle light only and there is no display neither hd or av im i doing somthing wrong ? btw the console is japanese falcon Edited December 31, 2023 by DARK A Quote Link to comment Share on other sites More sharing options...
lopenator Posted December 31, 2023 Report Share Posted December 31, 2023 (edited) that soldering looks horrible dude. I don't mean to be mean but I'm honest. Edited December 31, 2023 by lopenator Quote Link to comment Share on other sites More sharing options...
Donnie-Burger Posted December 31, 2023 Report Share Posted December 31, 2023 (edited) Use flux. many brands out there - Kingbo, Amtech etc This one is legit: (Super cheap, big container and lasts a long time) https://www.ebay.com/itm/143408532066 Edited December 31, 2023 by Donnie-Burger Quote Link to comment Share on other sites More sharing options...
DARK A Posted December 31, 2023 Author Report Share Posted December 31, 2023 47 minutes ago, lopenator said: that soldering looks horrible dude. I don't mean to be mean but I'm honest. yeah i know haha i did a better job on a diffrent console 2 Quote Link to comment Share on other sites More sharing options...
DARK A Posted December 31, 2023 Author Report Share Posted December 31, 2023 57 minutes ago, DARK A said: i try diffrent console i got read nand no problem and i creat and write xell no problem i try booting the console with eject to get the key it turn on by flashing the middle light only and there is no display neither hd or av im i doing somthing wrong ? btw the console is japanese falcon read this 29 minutes ago, Donnie-Burger said: Use flux. many brands out there - Kingbo, Amtech etc This one is legit: (Super cheap, big container and lasts a long time) https://www.ebay.com/itm/143408532066 thanks but i did a better job on the next console 1 Quote Link to comment Share on other sites More sharing options...
DARK A Posted January 1 Author Report Share Posted January 1 (edited) i figured it out what the problem was it was cpu rst the alternive one showed in mario video it wasnt working for me i did the one under the xclamp now everything was working untill i connected the dvd now sometimes it boot sometimes it dont and show red light i think my cable management is very bad or is it something to do with the dvd ? and if its the cable management can someone show me a better management for all the wires ? Edited January 1 by DARK A 1 Quote Link to comment Share on other sites More sharing options...
Donnie-Burger Posted January 2 Report Share Posted January 2 22 hours ago, DARK A said: i figured it out what the problem was it was cpu rst the alternive one showed in mario video it wasnt working for me i did the one under the xclamp now everything was working untill i connected the dvd now sometimes it boot sometimes it dont and show red light i think my cable management is very bad or is it something to do with the dvd ? and if its the cable management can someone show me a better management for all the wires ? This is normal on some rgh 1.2 installs. Its interference with the pulse waves during glitch cycles. Can you show some pictures of your wire routing? Are you using a resistor on PLL? If you are what value? Are you using Diode on post? If so the right one? Also, what chip and timing file are you using. Some will behave oddly. I like to test with dvd re-attached and top case installed. These 2 will change your glitch values sometimes. I only RGH 1.2 phats now since rgh3 can be picky on some phats. Slims I RGH3 all day and noticed that some trinities will short resistor and you will get black screen at boot until you replace or remove resistor. Coronas have never done this to me so I've opted to not use resistors on Trinity mobos anymore. Use this J-Runner from Octal450: https://github.com/Octal450/J-Runner-with-Extras/releases/tag/V3.3.0-r2 Hope this helped. Quote Link to comment Share on other sites More sharing options...
Bowlsnapper Posted January 2 Report Share Posted January 2 3 hours ago, Donnie-Burger said: This is normal on some rgh 1.2 installs. Its interference with the pulse waves during glitch cycles. Can you show some pictures of your wire routing? Are you using a resistor on PLL? If you are what value? Are you using Diode on post? If so the right one? Also, what chip and timing file are you using. Some will behave oddly. I like to test with dvd re-attached and top case installed. These 2 will change your glitch values sometimes. I only RGH 1.2 phats now since rgh3 can be picky on some phats. Slims I RGH3 all day and noticed that some trinities will short resistor and you will get black screen at boot until you replace or remove resistor. Coronas have never done this to me so I've opted to not use resistors on Trinity mobos anymore. Use this J-Runner from Octal450: https://github.com/Octal450/J-Runner-with-Extras/releases/tag/V3.3.0-r2 Hope this helped. Crap, I used a resistor on my trinity. Hope it doesn't die What makes this version of J-Runner special? 1 Quote Link to comment Share on other sites More sharing options...
Raidernick Posted January 2 Report Share Posted January 2 (edited) 5 minutes ago, Bowlsnapper said: Crap, I used a resistor on my trinity. Hope it doesn't die What makes this version of J-Runner special? I've done rgh3 on around 8 trinity boards using a resistor and have never had an issue with them not working or breaking at a later date. Also there is nothing special about that jrunner it's just the latest version. Edited January 2 by Raidernick 2 Quote Link to comment Share on other sites More sharing options...
Donnie-Burger Posted January 2 Report Share Posted January 2 10 minutes ago, Bowlsnapper said: Crap, I used a resistor on my trinity. Hope it doesn't die What makes this version of J-Runner special? If you get any boot issues check that. Best version bro. Octal pretty much continued the work. has all patches, most timnings, etc. I have issues with the sonus part of it. For that I load up an older version of JR. 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.