DARK A

sorry for the late replay the only version i try it on was v1 and i only followed ss_dave info all i did was removing the jumper wire infront of the left capacitor and the yellow transister right to right cap and it worked btw im not electraion so responsible for any damge that it may cause i only followed dave info here is the picture of the same psu v1 for both pal and ntsc and what to remove but be careful https://imgur.com/a/g5nWjqw

sorry everyone for the inconvenience but let me explain what happened i didn't look inside the port with a camera because i already cleaned it with 99% alchool and a toothbrush two times so i thought there was no need to look at it but thanks to allah then fringle for his replay i took a picture inside the port and look what i found a piece of plastic how did it get here and where did it come from ? my guess is its from the one who owned it before maybe it was on top and after multiple connecting and disconnecting it fall after i removed it the hdd working no problem thank allah so thank you everyone so much and sorry for the inconvenience im gonna just disconnect the dvd and use the console without it

i was going to do that and i put thermal pads on the memory and got a new psu and i was ready to put it back toghter untill i found out the hdd is not working the weird thing is i have another retail flacon i did test the psu with had no problem everything is working i was thinking maybe the pad the heatsinks caused some short to something im not electrician so i dont know to figure it out . btw thanks for the replay

lol no they are soldered i can glitch the console without dvd and play games from arura no problem, before the hdd problem started now i can launch aurora from external hdd no problem only if there is no dvd so you think it could be my coolrunner soldering is the problem ?

how to do that ? and btw i have zero knowledge in electricity here you go https://imgur.com/b1ERupR https://imgur.com/b1ERupR https://imgur.com/gXlP1lH https://imgur.com/fEtExEX https://imgur.com/lsKKmgw https://imgur.com/BnqvA0E https://imgur.com/Ahw2jyu https://imgur.com/PVokFRS https://imgur.com/6NGOyed https://imgur.com/lNwzf6W https://imgur.com/29fvzkz im using rgh 1.2 so no resister im using cool runner how to look for shorts on the pins and which pin is that its been booting before i added thermal pads and heatsinks to memory and before using the new psu only the dvd will not make the console boot it make cool runner blinking green forever btw its fat not slim so i dont think its sata bus

i didnt mean it make it glitch i mean it doesnt make it glitch and no it doesnt boot to xell if its connected i have to unplug it

can i use external drive as the main drive for the console via usb ?

it has more wattage but its the same as old one 12v , if i did really fried it what can i do ?

yes i try different hdd same thing it doesn't show up in storage

yeah i know but most people here know a lot about 360

hello everyone i finished rgh 1.2 my falcon 360 everything is working except the dvd drive it dosnt seem to make the console glitch it just stuck in loop so i removed anyway i was thinking of cooling the memory so i added a thermal pad and heat sinks to these , (ps not my picture ) and after that it doesn't recognize any hdd connected i try the hdd in another console its fully working i removed the pads same problem what can be the problem ps i got a new psu since someone told me that maybe my old psu is faulty (after i added the pads i didnt try the console with old psu so i dont know is it the new psu that killed the port or is it pads or somthing else ?) and its much higher watt 203watt i try it in a diffrent console before trying it on this console and didnt have problems

which version do you have ?

anyone can help ?

i try directly into the wall now its yellow or green im not sure , anyway the cool runner now blink 3 times then stop for 2 secend on repeat i left it for 5 minutes same thing no booting or display

thanks for the info

sadly no yes red sometimes yes

i already got them away from each other when i was managing the wires just to make sure is post and cpu on cool runner a and d ?

im not near it to take picture . its rgh 1.2 so no resister or diode im using mario tutorial im already using jrunner with extra i did a better wires managment and it boot now no problem if i did not connect the dvd it work with hdd no problem the problem now only with the dvd what can be the cause ?

i figured it out what the problem was it was cpu rst the alternive one showed in mario video it wasnt working for me i did the one under the xclamp now everything was working untill i connected the dvd now sometimes it boot sometimes it dont and show red light i think my cable management is very bad or is it something to do with the dvd ? and if its the cable management can someone show me a better management for all the wires ?

read this thanks but i did a better job on the next console

yeah i know haha i did a better job on a diffrent console

i try diffrent console i got read nand no problem and i creat and write xell no problem i try booting the console with eject to get the key it turn on by flashing the middle light only and there is no display neither hd or av im i doing somthing wrong ? btw the console is japanese falcon

its not the flash its the nand i think its corrupted. my output is i try both hd and av nothing shows up. yes after using picoflasher every time i read and write i got successful with no errors. no i only get middle light blinking and some times 2 red light up right and down left

i figured it it wasnt my soldering it was jr programmer it wasnt working that good i switch to picoflasher and its fully working . so how to retun to stock or working nand now ? because i lost my original nand , my console is falcon or is the console done for ?

im using the wires that came with jr programmer