Jump to content

Search the Community

Showing results for tags 'trace'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Subscribed Members Only
    • Subscribed Members Only
  • Off Topic
    • New Member Introductions
    • Rumble Pit
    • Suggestion Box.
  • General Xbox Discussion
    • General Xbox Discussion
  • Original Xbox Modding Forum
    • Hardware Mods
    • Modchips
    • TSOP Flashing
    • Softmods
    • Repair
  • Xbox Case Modding
    • Case Mods
    • Lighting & Electrical Mods
  • Tutorials
    • Official Tutorials
    • Tutorial Submission
  • Software
    • Bios
    • Dashboards
    • Installation Disks
    • Applications
    • Games
    • Emulators
    • Homebrew
  • Xbox Collecting
    • Xbox Collection Showcase
  • Rare and Uncommon
    • Rare and Uncommon Xbox Hardware
    • Rare and Uncommon Xbox Software
  • Vendors
    • N64 Freak's Products
    • Barnito's Products
  • Development
    • Rocky5's Projects
  • Online Play
    • Game Night
  • Classifieds
    • Wanted
    • For Sale
  • Moderator Section
    • Moderator Back Room

Product Groups

  • Vendor Forum
  • Membership Subscriptions
  • Forum Ads

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


About Me

Found 5 results

  1. Hi, I have been given two Xbox consoles, one to repair (and I may get to keep the other), both new to me and have been in storage for years so owner is unsure of details. Both hard modded. One works fine, the other after fixing an overheating issue now works to turn on intermittently using the power button. Eject seems to work OK. The hard mod requires the use of the power button, it will work after 5 or so minutes of fiddling. Because I am in a unique situation I am looking for advice that I can't search in another category. I have been asked to get photos and saved games off the non working box. My soldering skills are limited and kynar wire will cost me $20 here in Australia so I'm hoping there might be another fix. Given both boxes are hard modded is there a way to unlock the drive in the non working box and use it in the working one? I have been told that a straight swap didn't work which is why it's been given to me to find a fix. I've read about nulling the HDD and eeprom but all info seems to be based on a softmod. I have contemplated several options but not sure what will be simplest, lowest risk etc. Cloning - can I clone a drive from one box and use the data in another? Swap - Is this possible? Do I need to null the HDD and eeprom on both boxes? Can I look up the eeprom code on the working box and change the HDD code to match? FTP, can I simply FTP the data from the non working box and then push it to the other box? (Keeping in mind by non-working I mean it takes 5 minutes to get the power button to boot into the hard mod. Finally a hardware fix. As I said my soldering skills are limited so I'm worried about this proper fix for now (though it may be easiest and will result in two working boxes). Thanks in advance for your suggestions.
  2. Hi I'm currently doing a lpc rebuild on a 1.6 og xbox and I've managed to lift the trace on the trace near R7P4 does anyone know if theres somewhere else on the board I can pick this up? Thanks in advance.
  3. My old eyes and lack of soldering skills has caused a problem. Plan was to TSOP a 1.0 Xbox. Top side bridge R7D3 went fine, but on the bottom of the board at R7R3 I burnt off the pad and the trace lifted up (bottom arrow). Can I solder a wire from the lifted trace to either the pad above it if I can get it to stick or the surface mount resistor above that pad (seen in pic)? Xbox is softmodded and still working. Maybe i should just quit while I am ahead lol
  4. Hi guys, So I've got a problem just like the title says my Xbox is being weird and not turning off. I've opened it up, removed the clock cap and cleaned up the very minimal corrosion that I could find and gave it a good scrubbing with a soft toothbrush and isopropyl, I've inspected the traces, poked around with my multimeter and have continuity happening and can't see any damage at all even under a magnifier. But I'm getting some odd symptoms that I've read about where I can't turn it off and it opens the dvd drive. Now the reason I find this weird is that it doesn't happen all the time, from a cold boot it's totally fine, but I lose the ability to turn it off only after the xbox has been on for about 30 minutes. Wondering if you guys can think of any other things that could be the problem? Thanks!
  5. Hello, I've got an xbox to which I've performed the trace corrosion repair on the past, as the buttons did not shut down the console properly (it only turned on after i applied power to the unit). I've ran it just with the power button working, until now, when I decided to go ahead and try to fix both buttons. But now it went bad or something, because no matter how hard I jump wires to traces A, B and D (C is fine on my board, and I can't find E) as shown on this thread, the console simply refuses to turn on anymore.the wires are just fine and they give me continuity when soldered, but that's that. I know for sure that the power supply is perfectly fine (it never really failed). Even with only traces A and B soldered properly I can't get the console to boot anymore, and the right hand side of C7P8 has continunity to the solder pad in trace D (just saying because i'm not sure if this is how it should be, I hope nothing shorted ). Is there any other way to wire the power to the board so it'll work again? It would be really bad to have to throw it away over something like this.... I really hope someone can help me. Thanks in advance.

Board Life Status


Board startup date: April 23, 2017 12:45:48
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.