Search the Community

Removing the delay from the window where the game video is running without it blinking when loading every time you make a move, or at least make the video appear before the slider goes down completely

Evening everyone. Tried to post this on /OriginalXbox and for some reason my post isn't going up even though I've been active in it for sometime now. Anyway here is what I am trying to do: Hey fam! I have a 6 Xboxes. 3 are 1.0 and all have chips. 2 Jafars, one x2.0 pro. Most had issues one way or another and I had the chips lying around anyway. So out of convenience at the time, I installed them. I figure I don't need them in there. I already understand the "if it ain't broke, don't fix it." I just want the chips for other boxes. Definitely not new to the OG, I've just never swapped mods other than chips. I have TSOP'd before, so bridging points is not a problem. I am just trying to figure out steps. These are my thoughts: Drives are all unlocked (partitioned, formatted, no retail/stock dash), so I am thinking pull the drives, rebuild to stock with FatXplorer, install the drive back in the box, then relock with the modchip still in. Pull the modchip and disconnect d0 Bridge points Boot from exploitable game Use SweetDarkDestiny's TSOP MC Flash Program or his flasher disc Profit? Just looking to see if anyone has done something similar and if this process sounds like it will work? Looking for any and all input other than "don't do it." If I mess up, I still have the chips right?

Hey, I've done a RAM upgrade on one of my consoles (1.4) and it's doing the on/off/on/off/on flash orange and red dance. I've reflowed the chips, scoured them with a magnifying glass for bridging and the rest of the board for splashes, and scrubbed the board with IPA hoping that if it was a splash, it'd be knocked loose, but I've had no luck. I'm at the point where I think it might just be some bad memory, so what would be the best way to remove the chips without damaging or moving the surrounding components?

Thank you in advance for any and all help provided, I was fortunate to have come across a X3 chip along with a X3 LCD Face plate. But my XBOX is TSOP, I haven't came across on the "how to" remove the TSOP instructions. Is this a possibility? My xbox is a v1.0 or v1.4(not a v1.6) I have ind bios. I don't think I made a backup of my EEPROM when I did the TSOP, not sure if this is relevant to this.

Hi, I have been searching for a way to disable the profile picture of XBMC4GAMERS. I only have one profile and it is set to auto load. Looking at /system/userdata/profile.xml there is the line <thumbnail pathversion="1"> that shows where the current image is located but if I delete it, there is still an empty square shown.... now how do I get rid of this square?

i have a new bottom shell that i'm going to transfer the guts of another xbox to. i would really like to take the date label off the old shell and put it on the new one(versus writing all the number on a piece of masking tape). is there any way to do this without destroying the label?

If i flash a bios with the skip dvd check will i still be able to boot from dvd on a blank harddrive?

I recently got a green xbox and want to sell my old black xbox. I want to remove the 500GB sotmodded hard drive and replace it with the original 8GB. I know how to do that but I want to be able to use the 500GB drive in my Green xbox - how do I do this? I don't mind formatting the 500GB drive and starting afresh. I have an IDE PC if that's any use. Any help greatly appreciated

Dear all I want to change power led color of og Xbox but can't remove front panel to gain access to power pcb, what is the easiest way to open it? Thanks

I would like to remove the DVD drive on my 1.0 tsop . Occasionally the Xbox will fail to boot because of the drive, and I have no need for it. I looked around on the internet and my xbox, although I know it can be done; I am not seeing clear way of performing this mod. Assistance would be appreciated.