Donnie-Burger

Step 1 would be 128MB ram upgrade I suppose. I assume the rest of the steps are the same as 1.0-1.5. I'm looking into perhaps doing a cpu upgrade on a 1.6 - Confirming cpu core voltage before proceeding.

LOL. I have one but has a crack on it

Anyone have a top and dvd bezel for a Halo Edition Console let me know. Need 1 to complete a set.

Check each leg with tweezers/ magnification or microscope as well.

Very good idea.

Thank you - So wingman is slightly cheaper per player.

Yeah just built a single with teensy 4.1 and was $60-$70 - Wingmans are $50 on amazon. $63.72/board is that for the 4 player version each slot you mean?

Whats the average cost to build one?

Try https://www.ogxbox.com/forums/index.php?/forum/16-for-sale/

Video port came off clean with hot air - 1.6 install:

Xiso or folder?

Works with kit and udma5 flavor.

How I do it: Make sure to flash Xblast bios and load it up to make sure its loading (On some modchips with multiple banks xblast wont load) 1. Remove ram chips from dead motherboard with flux and hot air + vacum pen (Tweezer cool too) (You don't need to ad solder to the legs 1st but you can as it makes the pull slightly easier) - Mechanic LT-201 - Cheap vacum pen - Non electrical and works really good $10 2. Clean new ram slot with ipa or acetone then Flux + Tin with leaded solder. Now use de-solder braid to pick up excess solder and make the pads nice and flat/shiny. (I've tried many many de-solder braids over the years and MG Chemicals has been a Godsend - The newer style is even better). https://www.amazon.com/dp/B003AGEDVI?psc=1&ref=ppx_yo2ov_dt_b_product_details (I used to skip this step and slap ram chips in. Way better results doing it the right way. Sometimes get ram chip 1st try with no touch ups needed now). 3. Align new ram chip to corners - Tak down corners while pressing firmly down on the ram chip to make it flat on the board. When all ready and aligned you can solder each leg one at a time or use hot air to re-solder. I use hot air now and then check each leg one at a time with tweezers. Any legs move re-solder them/check again. 4. I have best results starting with underside but I don't believe it matters. After 1 ram chip is soldered fire up xblast and do the 128mb ram test. If all is good you should see success and 3 fails. Repeat 1 at at time until all 4 say success. Any frag'n in between testing is either ram chip not soldered right/leg loose/bad ram chip.

Thank You. I believe it's time for CPU Upgrade attempt #1

XBOX 1.6 + Make MHZ + Titan UDMA 5 = All good.

You are the man! XBOX 1.6 XBOX HD+ 1.6 Titan UDMA 5 128MB ND 256kb bios Thank you

Where did you source parts?

What an epic pack. Thank you for sharing!

Came in today

Seller on etsy has them all. https://www.etsy.com/listing/959450643/original-xbox-replacement-jewel?ref=yr_purchases https://www.etsy.com/listing/959451927/original-xbox-replacement-controller?ref=yr_purchases

Current builds that are in 1.4 Xbox 1.6 Xbox To do list: Make MHZ CPU Upgrade Finish refurbing controllers Another project:

Yeah 1.6 with cpu upgrades would be best models I would say. I'm willing to give it a shot if anyone finds the values.

You are welcome. Is there anyway to incorporate xiso support into titan, seems like make mhz and xiso is the only goodies missing, or am I asking to much? Any bios you want tested let me know and thank you again.