GyTe Posted November 17, 2022 Report Share Posted November 17, 2022 Long time reader first time poster! Sorry to start in this way but I'm completely lost and if possible I need your help all... First disclaimer, before the attempt on both console to install the modchip everything works fine (stock console no softmod or other modchip). As per the title I've installed the same Aladin XT Plus 2 (pick-up from AliX) but at the end (after the first boot) both console start to have the same issue as per below : Tries to Boot 3x then FRAG (Christmas Lights) Usually due to a failed or improperly installed modchip or the IDE cable being plugged in upside down somewhere. Check modchip wiring and IDE cables. If you did not do any soldering, it could be a bad PSU. - On both console I've already removed all the wires for the Aladin (beside the connector on the MB) - Cleaned everything with isopropyl alcohol - Replaced the power supply - Recaps (Done only on the 1.0) - Searched on the motherboard for broken component or any other strange visual sign of issue Is clear that the Aladin I've is faulty but what I can try now to revive those two console? Thanks! Quote Link to comment Share on other sites More sharing options...
Prehistoricman Posted November 17, 2022 Report Share Posted November 17, 2022 Do you know if the Aladdin is flashed? Quote Link to comment Share on other sites More sharing options...
GyTe Posted November 17, 2022 Author Report Share Posted November 17, 2022 Yes is flashed... I've also removed the SST stock (the one received with the microchip) and used another 49LF020A (That I know 100% that isn't fake)... Used an external programmer to perform the reflash of course... The strange thing is that after a single boot with this modchip, both console, now they act in the same way.... looks like the modchip brake something somewhere on the MB... Quote Link to comment Share on other sites More sharing options...
SS_Dave Posted November 19, 2022 Report Share Posted November 19, 2022 What happens if you boot with the modchip disconnected? Cheers SS Dave Soft modding is like masturbating, It gets the job done but it's nothing like the real thing. Quote Link to comment Share on other sites More sharing options...
GyTe Posted November 19, 2022 Author Report Share Posted November 19, 2022 With or without modchip don’t make difference unfortunately… at the moment 1.0 and 1.4 both frags and this happened just with one single boot with Aladdin xt plus 2 installed (Shame on me I’ve used the same modchip). In any case I did a visual inspection and both motherboards seems to be ok… clock caps already removed some months ago… checked even the power supply value, on 1.4 everything is ok… on 1.0 I’ve the 12 volt that’s a 11,6 volt. … I’ve some other 1.0 power supply but at least for now I won’t use… My understanding that modchip is faulty and make some mess on both motherboards… even because now they act in the same way… Quote Link to comment Share on other sites More sharing options...
GyTe Posted November 25, 2022 Author Report Share Posted November 25, 2022 (edited) A little update from my side : 1.0 motherboard for now the repair is put on hold... for the 1.4 motherboard, after a clean with ultrasonic cleaner, the console start again to boot and works as usual... For test I left the console on for 3 hours no issue so far...After that I removed again from the shell and prepared for 128MB ram mod, tinted the pads clean with isopropyl alcohol and tested again.... unfortunately same issue of before... frags red / green light... checked again all the pads for shorts ecc without luck... everything been done correctly. The caps seems to be ok but a recaps of the motherboard can help or is just a waste of money? Edited November 25, 2022 by GyTe Quote Link to comment Share on other sites More sharing options...
GyTe Posted November 29, 2022 Author Report Share Posted November 29, 2022 Another update : 1.4 MB put on hold the repair waiting for new caps 1.0 MB tried again to clean this morning and power-up but after 10 - 15 seconds I started to heard some strange noise from the area as per picture and a little smell of burn. Disconnected everything and checked with microscope and at least from my side I cannot see any burned component. I've checked caps and resistors nearby this area and I haven't find anything broken. At that point I'm starting to think that issue can be the Voltage Controller SC1103 itself or the voltage that will arrive on his pin number 1. As per schema below the max voltage is 14 Volt. So next steps will be to hook the multimeter to Pin 1 and check what's the voltage... If is within the range of 14 Volt (I suppose 12 Volt) the Vin is ok and maybe the issue is the voltage controller itself. Quote Link to comment Share on other sites More sharing options...
GyTe Posted November 30, 2022 Author Report Share Posted November 30, 2022 Done voltage check on SC1103 and seems to be fine.. input voltage on VCC 11,92 Volt (this means the 12 volt line is ok) output voltage on BST 11,92 Volt... Quote Link to comment Share on other sites More sharing options...
GyTe Posted December 1, 2022 Author Report Share Posted December 1, 2022 Received yesterday another stock of Aladin XT Plus 2. They're arrived already pre-programmed with Evox for 1.6 mb. I've removed the eeprom and programmed with the right version compatible with 1.4 MB but no luck... still frag... tried even to use Cerbios same story... so at least for now 1.4 MB will be put again on hold waiting for new capacitors. Quote Link to comment Share on other sites More sharing options...
GyTe Posted December 12, 2022 Author Report Share Posted December 12, 2022 Received today new caps... Replaced on 1.4 MB but still frag... I've to find out what's the issue... Quote Link to comment Share on other sites More sharing options...
KaosEngineer Posted December 12, 2022 Report Share Posted December 12, 2022 Post some pictures of the LPC pin header solder joints. Edit: Did you connect a wire from the BT pad to ground on the modchip to always enable it? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.