Jump to content
k0mpresd

Aladdin Xt + 49lf080a + X2 5035 Bios

Recommended Posts

aladdin xt chips.
flashed to support 1mb 49lf080a chips.
currently programmed with x2 5035 512kb bios (2* banks with same bios). can be changed at buyer request.
 
$25 posted to usa. international available.

Please login or register to see this attachment.

Share this post


Link to post
Share on other sites
1 hour ago, suwuj12 said:

Xblast? 

The Aladdin XT plus  chip can have the LC4032 chip flash to be a single 1024kb(1meg) with write protect ,dual 512kb providing that the 49LF080A is used. So it's a duoX2 chip in other words

If it flashed as a Xblast it' has a 1 X512kb and a 1 X256kb Bios using the 49LF080A

 

Cheers

SS Dave


Soft modding is like masturbating, It get's the job done but it's nothing like the real thing

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Content

    • By FerociousOG
      Unable to flash BIOS. Error reading bios file (see pic). To me it sounds like I have a bad DVD burn? Just wanted to confirm. I did burn at the slowest write speed. Will re-burn again.
      -v1.1 mobo
      -XeXEn 2018
      -Using Verbatium DVD+R media
      -Attempting to flash iND-BIOS.5004 (F and G) to use 2TB SATA HDD.

      Thanks in advance.
       
    • By Listai
      Please login or register to see this link.
      Hi everyone
      Yesterday I ran into an issue with my install - I have a 1.6 Xbox so I picked up an Aladdin XT and a rebuild board to make the job easier. Should be easy right? - apparently not as I stuffed it up. Basically I made the mistake of following a video where the rebuild board had a much larger space around the pins which allowed for quite a bit of solder to be flowed onto them - I followed those instructions and when I went to put my board on it didn't sit flush. So for whatever reason I decided to solder it in and see what happened.
      Naturally, it didn't work so I with armed with a lot of patience and a desoldering wick I managed to remove it without destroying any pads or traces - but I have another problem. I didn't remove the unnecessary pin headers for my 1.6 - will the chip still work? and do I need to solder all of the pins to the rebuild board (I'm confused about the plating corresponding to each of the pins) as I'm not sure if I can remove them as you can see from the image the solder has gone directly into the through hole and I don't have the means of removing it.
      Sorry if this is stupid but I barely managed to get the header off of the board (thankfully I ordered extras) I don't want to have to desolder another one of these.
      Thanks!
    • By Paw
      Hi guys i just found my old xbox in the basement and by the look of things it looks like its hardmoded with a Xecuter chip and there is even a 120gb drive installed and all is working without any issues. My main question is if anyone here could help me identify what kind of Xecuter chip this is, because my plan is that i would like to replace the 120gb drive with a 1tb but im getting a LBA48 warning when i try to partition the new disk and its asking me to ugrade the current bios with a new one that supports LBA48.
      Current INFO:
      Bios: Xecuter2 4976.02
      Kernel 1.00.5838.01
      Xbox v1.1
      What would be the best course of action, how should i approach the reflashing, what bios should i pick so that the new 1tb drive works as intended and ofcause what should i think about when i approach all this?
       
       
      Please login or register to see this attachment.
      Please login or register to see this attachment.
      Please login or register to see this attachment.

Board Life Status


Board startup date: April 23, 2017 12:45:48
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.