Jump to content

Search the Community

Showing results for tags 'about'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Off Topic
    • New Member Introductions
    • Rumble Pit
    • Suggestion Box.
  • General Xbox Discussion
    • General Xbox Discussion
  • Original Xbox Modding Forum
    • Hardware Mods
    • Modchips
    • TSOP Flashing
    • Softmods
    • Repair
  • Xbox Case Modding
    • Case Mods
    • Lighting & Electrical Mods
  • Tutorials
    • Official Tutorials
    • Tutorial Submission
  • Software
    • Bios
    • Dashboards
    • Installation Disks
    • Applications
    • Games
    • Emulators
    • Homebrew
  • Xbox Collecting
    • Xbox Collection Showcase
  • Rare and Uncommon
    • Rare and Uncommon Xbox Hardware
    • Rare and Uncommon Xbox Software
  • Vendors
    • N64 Freak's Products
    • Barnito's Products
  • Development
    • Rocky5's Projects
  • Online Play
    • Game Night
  • Classifieds
    • Wanted
    • For Sale
  • Moderator Section
    • Moderator Back Room

Product Groups

  • Vendor Forum
  • Membership Subscriptions
  • Forum Ads

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


About Me

Found 11 results

  1. Hello I'm new to the Xbox forum,I want to learn as much as i can about it. I want a place to talk about the xbox so I hope I'm in the correct place lol Thanks K-9
  2. Hi guys, First off I want to thank everyone for their help along the way I've learned a lot from this forum sure I could have had other people do it for me But honestly I wouldn't have learned as much but I still have a few questions so I'm going to go ahead and post them here (1) I have a whole bunch of burn CDs for the Dreamcast could my Xbox read them? (2) with my 500gb IDE drives now installed 110 gig devoted new Xbox games another 80 for coin-ops and probably another hundred for SNES What would you add now if you were me (3) I'm thinking of skining my Xbox is there a site still that I can get skins I really don't want to paint the unit I could buy a bus in Xbox and paint it that case and then just transplant my own but I really don't want to go to the time and after that
  3. can i replace 3300uF 6.3v capacitors with 3300uF 10v ones ? got a 1.6 Halo box that is almost in prestine condition apart from being opened by me and all 5 capacitors next to the mobo power connector are popped. the only replacements I have at hand would be the aforementioned 10v ones that I scavenged from a v1.2 board.
  4. Hello everyone. Quite new to this site, I was more active a couple of years ago when it came to the OG Xbox, but since, much else in life has taken it's time,, and I got stucj in the RGH business some years,, and I notice how quickly the memory fades. So now, when time has come back to dust off the old consoles that's been standing in the closet for some years now, many of the sites has been gone with the wind,, but, then I found this one : and I'm glad to see that the OG Xbox community still flourishes,, with a lot of new updates and upgrades since I last installed XBMC from a AID 4. disc. So,, I thought I would see if there's any bright minded folks that know something about a chip I discovered in a recently purchased 1.6. I searched about it but all I come across is dead links. The chip is a Muppet-X,, neither Kermit or Animal, but a white one with a 4 pin connector where only D0 is used, no BT etc,, those I removed, just want always on mode. But, I can't find any information about flash bank sizes, or the switch, so I have not been able to update the bios on this rare thing. So is there anyone with information about this thing I would be grateful.
  5. Hi witch bios allow to boot the xbox without a dvd drive ? and witch config i need to change ?
  6. To be honest I'm just not sure If I should swap my softmoded MB to the halo edition or softmod them both. I honestly want to sell the MB but I donk know how to show its a Halo Edition on the /MB. ANY ideas ?
  7. So I really want to upgrade the HDD but I'm super worried about bricking my system. How risky is it and what are the best steps to take for preventing a brick?
  8. Hi; About two years ago I bought this used ModChip for 10 USD, but I really don't know what kind of Aladdin version is, It's my knowledge that Aladdin ModChips have a lot of versions so I need your help people to identify it, and if you can or have it, I need install instructions too, please, I remember that this chip can be compatible whit all motherboard versions of original Xbox, and I remember that actually we don't need too much points to install this kind of chip (Aladdin) to make all the steps for have a mod original Xbox because there's no more Xbox Live (for example) for this wonderful console, but I'm only speculating based in my memories, you're the experts, I really appreciate your help and time
  9. This is my frist time working with a Tsop im looking for advice ik i got 1..0 1.1 versions does this wire need to be a single copper or can it be threaded also hexen i can find but a bios checker i can not fine any where
  10. Cool video about xbox development, i wonder what your thoughts are, and has anyone got more of this content to share? I'm curious about what PC ports exist and what may have been possible Just read through RandySlims post here, he has a good list of games... nice to run into 'digthatbox' again... its outside of my oxbox TUNNELVISION so i guess i forgot about it
  11. I rebuilt the LPC port on my Xbox v1.6 today and had kind of a tough time with it, so I'm curious what everyone else uses to mod their consoles; type of wire, flux, solder, soldering iron/station, soldering tip, soldering temperature, cleaning solution, etc. I used some 30AWG wire-wrapping wire from Amazon, an Aoyue 937+ with the fine tip that came with it, RadioShack rosin flux paste, and RadioShack 62/36/2 rosin-core solder. I've soldered quite a few 0.1" headers on microcontroller and FPGA development kits with great success, but their pads were like twice as thick as those on the Xbox's LPC port. I had a hell of a time getting the pads to heat so that the solder would flow nicely. I also ended up burning the solder mask in a couple of places where I left the tip on too long trying to get the pads heated. Fortunately it still seems to work, but the joints look pretty bad. I think part of the problem was the fine solder tip, but I didn't have much luck with a chisel tip either.

Board Life Status


Board startup date: April 23, 2017 12:45:48
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.