Bowlsnapper

Why not buy an RF shield? Or I guess you could use HDMI if you wish. Yes, the HD+ does work very well. Stellar is pretty cool too. You will either need Nemesis' STM32 dev board to use the HD+ without the stellar, or buy the standalone kit from MM. I would TSOP flash with Cerbios, which is compatible with the HD+ anyway, but don't be scared to change it. You don't have to be. But if you wait for the Open XHD, that is an option as well, and you will not need to deal with standalone STM32 horsecrap. How does the CF work for you? Why not a SATA?

Use magnification and flux. Get a set of helping hands. Use tweezers. Watch youtube clips on SMD soldering. ONce you get the hang of it, it's actually very easy.

I'm sorry they ripped you off. That's disappointing. If anybody here would like a Xenium, I am selling them, along with a 3d printed support and 1.6 rebuild. Ebay is perfectly safe though, I'm sure.

Apparently it works. People have done it. It makes it faster anyway. It also enables UDMA 5 (instead of 4) in many cases.

What does adding the 10k resistor do? same thing, just more of it? Also, why TF don't they just do it at manufacturing?

I'll start downloading. Give me a couple months. lol

Jesus Christ.

Look at the Elegoo Nepture 4. It's what I use and it ROCKS. Puts all others in it's price range to shame. I would get the Neptune 4 MAX now, though. Its bed is much larger and will allow you to print the "Slim" case. Also found this for the Halo Editions:

Try booting with the DVD drive disconnected and see what it does.

What you've done here, is basically what I want to do with a Halo Edition I have. 128MB, Nemesis Xenium Ice (I have like 3 massive bundles). Either with an HD+ or OpenXHD. REALLY nice job dude. Translucent smoke black PLA. What do you think, Marty ( @MadMartigan)? Should I pull the trigger?

I will work on it!

ENDGAME 8MB Cerbios Flasher & UX Dash Installer I am posting a mirror of the TSOP flasher utilizing the Endgame exploit. This means that no savegame exploit is necessary. Just a memcard or USB drive with a stock Xbox. Will also Install a basic version of UnleashX to get you started with something. Mega Link: https://mega.nz/file/lzcFBRqb#SdqDkbwJ5qQuD_Md6aXht6shgPiD1A_N27e4X7D8b9o --------------------------------------------------------------------- Use this as a starting point to maybe run the OGXbox installer that Sweet made! Very fully featured and handy! ------------------------------------------------------------------------------------------------------------------ Credit for this flasher/software goes to SweetDarkDestiny. I do NOT take credit for this. https://www.xbox-scene.info/forums/topic/437-endgame-8mb-cerbios-flasher-ux-dash-installer/#comment-833

I actually don't know if I'd call it "Nicer". I still have to work on making the supports less damaging in the slicer, and I have to research ways to do that. It still looks nice, but I actually think clear PLA will turn out better. This one is deformed, but only because it was not supported very well that time. I need help from somebody who knows how to customize supports. If I make the attachment points too small to avoid leaving markings, they will not stay attached and the model will just start cooking on the vat film... which means I only see failures happen the hard way and have to remove the BS cured resin from the vat film, which almost always scratches it no matter how careful I am. So failures (in this case, caused by making the supports small enough to break off without leaving noticeable marks... TOO small) are a big pain in the ass so I'm afraid to make the support points too damn small. This had minimal supports however, so If I use more, I may be able to make the breakoff points smaller and thus less noticeable and also have the model turn out much straighter and proper looking.

They fall off, and it's heartbreaking. Don't worry, they can be replaced. I honestly think they look better than the regular translucent white ones. You get what is pictured here in the top photo. 25 shipped.

Hope this helps you:

I have black filament mainly, but also have white. Are you asking if there is clear? I can print clear cases with my resin printer. I think they are also nicer when resin printed. I can also get clear PLA filament. I can probably get a rainbow assortment of colors for not too much if you have another color in mind. I'll have to mount one and see what you are referring to. It's ridiculous but I haven't actually tried one out yet. So let me do that and I'll get back to you on the dimension issue.

10 bucks shipped.

Everything you see up top for 40 shipped. 2X7 pin header, though... not 2X6.

For profiles targeting 1.4GHZ systems, does that mean they are more resource intensive but the upgrades can handle it?

I am so Instastoked. The N64 controller would work great with the XBE version of SM64! And other N64 games on Surreal, of course.

What I'd like to do is a mix of the Origins setup and CCI image set. Have foldered games for 720P XBEs and what not (any desirable mods) and ISOs for the rest. Obviously C would be redone because it's a nightmare, especially with no MS Dash on it.

I hope my emulator controller talk didn't make it seem like I did not appreciate. I DO! I wanna try all my controllers with it now! Nice work, dude!

Yes sir.

DUDE YOU DID IT! Right the fuck on! I would love to see you internalize this somehow or make the connections modular some how. Maybe you can make room for the internals by eliminating the DVD-ROM drive?

JLC is cheaper than PCBWay, but sometimes JLC can be a bit retarded and I give up and go with Way just so I don't have to answer dumb emails. lol. @KaosEngineer NICE work, dude. That information is awesome and I'm manually saving it on my HDD.