Jump to content
OGXbox.com

Xbox Intro Video / Custom Menu


Big Poo
 Share

Recommended Posts

Hey there everyone. I watched a video on YouTube on a Modded Xbox. During the initial startup of the Xbox, it shows an animation and a custom dashboard. Does anyone know how to add the animation before the menu shows up and how to customize the menu?? I have never seen this before except for this video. Any help would be most appreciated. Thank you.

Here is a Link to the Video: https://www.youtube.com/watch?v=uw91sVm2fkI&t=1s

Starts at 8:03 minutes

Thanks Again!!

 

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Similar Content

    • By Noob.Xbox
      Hello,
      I know PAL games can display 480p if a PAL Xbox is softmodded NTSC.
      But do those « forced » 480p PAL games are as good as native 480p NTSC games ?
      I explain my point : on a region free PAL Gamecube, you can force 480p on PAL games with Swiss. But some games aren’t as good as their NTSC equivalent in 480p, because they are optimized for 480i/576i mode, not for 480i/480p mode, and so they can have some issues with their pictures.
      So, my question is : do PAL Xbox games have this kind of optimization for PAL region, as Gamecube games, or are they strictly identical to NTSC ones ?
      Thanks for your answers.
    • By tmntx3
      Hi all! I'm having some trouble with installing an OpenXenium purchased from MakeMHZ into an Xbox 1.0. I'm relatively new to this, and have surely made some mistakes. When I start it up, it does this: https://imgur.com/a/HTHYrU2
      Here's what I know: 
      Stupidly, I soldered the D0 pad on the modchip to the 1.6 pad - that has been fixed. I don't think this is the issue, because I have a second chip that I did not make this mistake with, and it still does not work.  I didn't scrape the solder mask off LPC ports, and really had trouble flowing the joints. The one I'm most concerned with is the bottom right joint of the first photo. Can I run a jump wire from that to one of the nearby test pads?  I'm fairly confident the D0 pad on the modchip is correctly connected to D0 on the board - I tested the continuity from the chip to the both points on the board, and was good.  I have photos available here: https://imgur.com/a/FX7R43B 
      Thanks for any info in advance!! 
    • By Pickle
      Im looking for some ideas to try before I look for a replacement xbox. Im not sure if i can do anything else at this point.
      My xbox was soft modded for some time, but I wanted to do a tsop to unlock the drive and then put in a 2.5 inch 500 gb sata drive. I did the tsop (i have a v1.5) soldered the 2 point and flashed the tsop with hexen 2021 disc. Put in my sata driver with adpater and 80 pin cable and everything was great. I started uploaded the library that i have. I also removed the supercap.
      I was down to my really scrached discs and was trying to see i could get good copies from them, but gave up. I picked up some new titles and went to install them and the xbox wouldnt boot. I get the evo/xbox splash screen to a blank screen with the orange led. Tried booting hexen or soft mod or game disc and nothing.
      I tried cleaning out the dvd drive, that didnt help. The last thing i did with the drive was watch it with the cover off. It doesnt appear to be trying to focus nor does it appear to be emitting a laser. It does move the laser head unit on the rails. But i dont think this should stop a boot to harddrive?
      I went back to the ide drive and the 40 pin cable and no change. I tried combinations of hooking up pc cdrom to the ide and dvd on the power. Thought maybe the dvd drive was corrupting the ide bus.
      Ive checked my caps and board multiple times. The only thing i was suspicious of was a pin point spot on the nvidia chip, i hope it didnt melt itself inside.
      So thats where im at, i think my dvd is toast and maybe the ide on the motherboard is broken.
       

Board Life Status


Board startup date: April 23, 2017 12:45:48
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.