Jump to content
martinoss

Upgraded Ram, Yes! But, Installed Wrong Bios After That.

Recommended Posts

Hello guys

 

I have upgraded my ram in the xbox and that works flawlessly first i installed the xblast boot os and tested every chip and success.
then i installed ind 5003.67 and it works also correct but he did not see the G drive so i format it but still not seeing that partition.

I thought maybe i must install the BFM bios but now i think it was for an xbox 1.6 because he wont boot.
the xbox turn on then go of twice and then stay on but no screen.
Can i reflash the chip? with a pickkit or something other way.
Can i fix this? or do i need a new aladdin xt2 chip. and will they boot on an 128mb board with stock bios.
I dont know if the xbox run with a not compatible 128gb ram bios or that it will boot but takes only 64mb.

 

thanks for youre time.

Share this post


Link to post
Share on other sites

i cant edit the topic but i was back to my hobby room and tryed to do a hotswap with an other xbox who has a softmod or tsop but he says chip not writable.
so is this possible and how.
I have only one chip so i can't do the hot swap with a second chip. but only softmod or tsop i think that is the reason it wont work?

 

Edited by martinoss

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Content

    • By Benur75
      Hello Friends,
      I have started a new Xbox ( My wife will kill me). This time I took the time to give you some photos of my madness:
      Step1: Disassembling
      Please login or register to see this attachment.
      It was very dirty, this is a 1.1 version. I immediately removed clock capacitor (Yes a gamegear is also lying on the ground) and change thermal paste.
      Please login or register to see this attachment.
      Step2:  Hot water and soap cleaning in the kitchen on plastic parts
      Please login or register to see this attachment.
      Step3: The same for the shields
      Please login or register to see this attachment.
      Step4: Shield painting to prevent corrosion (EMI points will be paint removed after painting). This is the grey primer, after I put what I use black or white paints.
      Please login or register to see this attachment.
      Step5: And why don't adding more ram, this board is very nice. With help of my xblast lite, one chip after another.
      Please login or register to see this attachment.
      Note, that the chip N°4 gave me some problem, after test, the xbox start then stop, I check and redid the solder 3 times, after first, no boot problem on Xblast, but the chip was not anymore detected. So I decided to gently remove it, and to replace it with a new one. And it worked, I could go on with the last one.
      For people upgrading their Xbox, don't forget that a chip can fail even if it is new like for me if you realize bad solder and make a short circuit.
       
      Please login or register to see this attachment.
      As you can see, it remains some flux. It is a bit hard to remove all as I worked for a long time on chip N°4. (Near PSU connector)
      Step6: I have to confirm that everything is ok and check memory inside operating system. You can see after the last chip that XblastOS show 128 Mib.
      Please login or register to see this attachment.
      Please login or register to see this attachment.
      Inside tool menu (in settings), you can test your memory. This is what you have to do after each chip added. My prefered order is chip 2, the chip 3 ( both bottom side), then the 4th because some caps take lot of place to solder and finish by number 1.
      Please login or register to see this attachment.
      and finally check under operating system, to confirm that no blocks are failled. Some blocks can't be tested as they are used by operating system.
      Please login or register to see this attachment.
      Step7: DVD cleaning, Pot settings, new belt installation and Ide to Sata improvements.
      Please login or register to see this attachment.
      As you can see, I replace always jumper by solder ( master / slave) I had a case where the jumper falled during shippment.
      I also replace the 2 bad quality chineese capacitors bye Panasonic ones.
      Please login or register to see this attachment.
      The whole DVD case was cleaned with isopropyl alcohol, and also lens, motor.
      New greased has been applied to axles and caddy.
      DVD pot was 2400 Ohm. It is very often a too high value like this one. Samsung drives like value between 1900 and 2000 ohm.
      Look the copy  speed result after that: more than 6 Mb/s
      Please login or register to see this attachment.
      Who wants it ? I don't spoke about the Sata HDD. I will use ever a 500 Gb, or a 3tb ( I know xbox can only handle 2 Tb )
      If someone wants it and leaves in europe. I will put this box on stress test during a week and it will be ready for sale.
      It can also be delivered with original HDD ( Seagate IDE and for the future IDE2SATA adapter provided)
      If you are interrested in, send a PM.
      Bye
      Benur75
       
       
       
    • By antonic901
      Hello everyone! I want to perform RAM upgrade on my Xbox but I don't know which RAM I should buy. Here is the picture of the RAM from my Xbox:
      Please login or register to see this link.
      SAMSUNG K4D263238F-QC50
      So my question is which RAM should I buy? I found a couple of RAM chips on ebay and AliExpress but I don't know are they going to work on my Xbox. Here is the list:
      Please login or register to see this link.
      Please login or register to see this link.
      And, thanks in advance!
    • By Speeddragonn
      At first I started modding my OG Xbox for fun and preservation. But I really like playing with it. After a Rocky5 softmod (mrmario2011 tutorial), I decided to go TSOP. After tweaking my potention meter, to finally get 1 of the 4 hexen discs to read, and after fixing the dashboard with it. I now have a TSOPPED, 1.0 with 256kb evox m8+ f and g bios and a unleash x dash.
      In the changelog of the HEXEN2018 disc, it says that every bios is modified to work without disc drive.. But if I disconnect my disk drive, my xbox won't boot into his dash..
      So I would like to try to modify my evox m8+ bios myself with evotool to get rid of the dvd check. (to make sure I preserve my og xbox when the drive fails in the future).
      The only problem is, I can't seem to find the bios files on the internet, and I don't know how to get them off the Hexen dvd..
      Anybody got tips. And what is your opinion, should I use ind bios instead? And what's the best way to flash from the hard drive?

Board Life Status


Board startup date: April 23, 2017 12:45:48
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.