Jump to content

Search the Community

Showing results for tags 'red'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Off Topic
    • New Member Introductions
    • Rumble Pit
    • Suggestion Box.
  • General Xbox Discussion
    • General Xbox Discussion
  • Original Xbox Modding Forum
    • Hardware Mods
    • Modchips
    • TSOP Flashing
    • Softmods
    • Repair
  • Xbox Case Modding
    • Case Mods
    • Lighting & Electrical Mods
  • Tutorials
    • Official Tutorials
    • Tutorial Submission
  • Software
    • Bios
    • Dashboards
    • Installation Disks
    • Applications
    • Games
    • Emulators
    • Homebrew
  • Xbox Collecting
    • Xbox Collection Showcase
  • Rare and Uncommon
    • Rare and Uncommon Xbox Hardware
    • Rare and Uncommon Xbox Software
  • Vendors
    • N64 Freak's Products
    • Barnito's Products
  • Development
    • Rocky5's Projects
  • Online Play
    • Game Night
  • Classifieds
    • Wanted
    • For Sale
  • Moderator Section
    • Moderator Back Room

Product Groups

  • Vendor Forum
  • Membership Subscriptions
  • Forum Ads

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


About Me

Found 7 results

  1. My final skin of the night This has become one of my favourite games on the original Xbox Red Dead Redemption So I decided to make a skin for it enjoy Red Dead Redemption.zip
  2. So I tried to Tsop my Original v1.0 Xbox and I think I lifted the traces. Now it tries to boot 3 times and then boots with flashing red and green LEDs. No audio/video. Is there anyway I can fix this? Alternate traces?
  3. Hi all, I have an X3 modded box that I have been painstakingly adding the Xbox game collection to over to. Last night while testing a few games the screen froze and when I looked at the Xbox I had a flashing red led. I assumed I had overheated for some reason and so I went to bed and left it to cool down. i have just switched it on again and it’s stone cold and still had the flashing red led, also my x3 chip is always disabled. Anybody have any ideas what’s going on? Im going to take it all apart and rebuild it again see if that helps. The last mods I did were to replace the fan with a Noctua one and to replace the thermal paste on the cpu/gpu. This was few days ago and it’s been running fine until now...
  4. I tried to mod my Xbox by doing the solder bridge mod to reflash the bios, I am now getting a flashing eject button red and green, I removed the solder bridges already, I also removed the capacitor for the clock. Any ideas what I can try to fix this?
  5. Hello gents This afternoon I received original Xbox 1.4 purchase from eBay. I turned it on. And stayed on for about 30min. Then I when head with Tsop. After that I run this Xbox for few hours. Transfer ninja pack, and enjoyed games for some time. Turn back on after dinner and red light start flashing. Normally I would say over heating, but I'm not sure. Could be eeprom as well, 8 pin chip next to bios. And a suggestion please ? Thanks Sent from my ONEPLUS A5010 using Tapatalk
  6. Into quite a bit of a mystery here. Sold a fellow a modded Xbox and he traded in an old busted Xbox to save a few bucks so now I'm trying to fix it. When turned on the Xbox turns off pretty quickly but then restarts immediately, then the same again, turns off and then back on a third time and then stays on and shows flashing orange and red lights (the odd time it will flash red and green just to deepen the mystery). Googling the problem results in many ppl saying it's an 'av pack' issue if the av cable is not the problem but the restarting thing tells me it's more likely a PSU issue or a bios/mod-gone-wrong problem. Pulled everything apart completely, thought I found the problem with a burnt contact point near the plugin. Re-flowed all 4 points just to be sure and no difference at all. Kept googling and found a few encouraging leads including this url https://www.xbox-hq.com/html/xbox-tutorials-163.html#xboxerrorcodes1 and tried jumping that wire from the lpc pin 5. No f*ckin' joy. Also just a side note - the lpc vias are all plugged with solder (see pic) indicating that a modchip was removed at some point. Also I checked the solder points for the Xbox 1.0 TSOP and it looks like they've been done also - but the guy said he never modded that one. Thing is, the further into this I get the more convinced I am that this unit is fixable. Most people will just say eff it and chuck it or whatever but I really like to save old things if at all possible. I have included a pic of the wire I jumped (yellow wire) from the lpc pin 5 as the url tutorial suggested. The same pic also shows a mysterious blue wire that was here before I opened it. Asked the dude about the blue wire and he said no idea, never modded that one. In some of my Googling I found a post saying something about a D0 wire or DO wire described as a 'modchip enable wire', maybe this could be it? Any ideas about how to move forward or what the blue wire is for would be great, my thanks go out to anyone who has any ideas that might help,
  7. I'm in the middle of a small project to repair a spares or repair Duke and I'm thinking of converting it over to a USB connection (as one of the problems is a frayed cable) and everything I've read says that I don't need the red wire that's in the original cable. Obviously you couldn't get it to work with USB if you did, but I'm curious as to what it's used for if I don't need it. So far I've seen it called "Video Sync", +12V and VCC, but that doesn't tell me why it's there. Except maybe for "Video Sync", but why would a controller need video sync?

Board Life Status


Board startup date: April 23, 2017 12:45:48
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.