Jump to content
OGXbox.com

Search the Community

Showing results for tags 'during'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Rules
    • Why Can't I Download?
  • Subscribed Members Only
    • Subscribed Members Only
  • Off Topic
    • New Member Introductions
    • Rumble Pit
    • Suggestion Box.
  • General Xbox Discussion
    • General Xbox Discussion
  • Original Xbox Modding Forum
    • Hardware Mods
    • Modchips
    • TSOP Flashing
    • Softmods
    • Repair
  • Xbox Case Modding
    • Case Mods
    • Lighting & Electrical Mods
  • Tutorials
    • Official Tutorials
    • Tutorial Submission
  • Software
    • Bios
    • Dashboards
    • Installation Disks
    • Applications
    • Games
    • Emulators
    • Homebrew
  • Xbox Collecting
    • Xbox Collection Showcase
  • Rare and Uncommon
    • Rare and Uncommon Xbox Hardware
    • Rare and Uncommon Xbox Software
  • Vendors
    • N64 Freak's Products
    • Barnito's Products
  • Development
    • Rocky5's Projects
  • Online Play
    • Game Night
  • Classifieds
    • Wanted
    • For Sale
  • Moderator Section
    • Moderator Back Room

Product Groups

  • Vendor Forum
  • Membership Subscriptions
  • Forum Ads

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


About Me

Found 4 results

  1. OK, I had a lot of trouble getting the AV port out of my v1.6 XBox. The solder pump I was using removed the traces on the underside of the board. Traces on the top are fine so I am able to tap the SPDIF and 5V. However, on the bottom, I tried using bodge wires soldered directly to the resistors going to pins 11, 12 and 13. My work so far has unfortunately been messy at best and I am getting flashing orange when starting the XBox so I am pretty sure it is my bodge work that is the issue. Does anyone know if there is a better way to short pins 11/12 and 13/14 elsewhere if my AV port through holes are toast? Reference picture of pins below... http://i.imgur.com/pyjq4y6.jpg BTW, the specific behavior I am seeing is I get a green light on the Xbox initially. The HD+ blue light blinks slowly (about every 3 seconds on 3 seconds off). After 10 or so seconds the Xbox flashes orange and needs to be unplugged to turn off. I did check the ribbon cable installation a couple of times. I checked for bridged connections. I also checked that I got continuity all the way from the ribbon far edge to the opposite side of the resistor that the trace was soldered to. So I believe the cable is soldered correctly (I'm sure, however, I could be proven wrong). I also tried checking continuity from by bodges to the other side of each resistor and had mixed results. I checked my soldering and it appears to be good. Not sure if maybe I fried the resistors if that is possible. Maybe I need to jump across the resistor (not sure if they do anything when pins 11/12 and 13/14 are bridged).
  2. Hi I'm after a bit of help; my Xbox 1.0 just crashed during a bios flash (I was using HeXen 2018) My Xbox will no longer boot (HD Error 05) and I don't have the adapter to flash my modchip on my PC. Unfortunately I can't even recall what my modchip is, and I've long since lost the PC (Parallel?) adaptor it came with. I've included a picture of the modchip, in case anyone remembers what it is. Should I buy a new modchip? My soldering skills are not great so if there is any way of salvaging this solderers chip I'd be grateful.
  3. I was testing an Xbox I picked up at the weekend and noticed it freezes during gameplay - would new thermal make a difference or do I need to just use it as a system for parts? Thanks
  4. I wasn't sure whether to post this here or in repair, but since it happened during a TSOP mod I though I'd try here first. Picked up a 1.4 version at a Salvation Army today, green model worked great but filthy inside. Cleaned it up, removed clock capacitor and did the two TSOP points. Reassembled and before I even load into Hexen my video signal has lines going across the screen. After messing around I find that the problem is only with component output (hd output) and standard def av works fine. Thing is, component worked fine before I disassembled so I'm convinced the problem must have been caused by something I did - but all I did was pull the clock cap and do the 2 tsop points... Tried another component cable.. same result. Tried another tv, got a glitched looking display or 'mode not supported'. I'm convinced it's now outputting some garbled attempt at an hd signal that neither of my tvs can process correctly. Have 2 other xboxes and both display hd perfect with the same cables and tvs. I guess I can just sell it with some standard cables but losing the hd kinda kills the awesomeness so I'd really like to fix this if possible. This is like the second weird obscure xbox mystery for me in like a week, sheesh:)

Board Life Status


Board startup date: April 23, 2017 12:45:48
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.