Jump to content

Search the Community

Showing results for tags 'removal'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Rules
    • Why Can't I Download?
  • Subscribed Members Only
    • Subscribed Members Only
  • Off Topic
    • New Member Introductions
    • Rumble Pit
    • Suggestion Box.
  • General Xbox Discussion
    • General Xbox Discussion
  • Original Xbox Modding Forum
    • Hardware Mods
    • Modchips
    • TSOP Flashing
    • Softmods
    • Repair
  • Xbox Case Modding
    • Case Mods
    • Lighting & Electrical Mods
  • Tutorials
    • Official Tutorials
    • Tutorial Submission
  • Software
    • Bios
    • Dashboards
    • Installation Disks
    • Applications
    • Games
    • Emulators
    • Homebrew
  • Xbox Collecting
    • Xbox Collection Showcase
  • Rare and Uncommon
    • Rare and Uncommon Xbox Hardware
    • Rare and Uncommon Xbox Software
  • Vendors
    • N64 Freak's Products
    • Barnito's Products
  • Development
    • Rocky5's Projects
  • Online Play
    • Game Night
  • Classifieds
    • Wanted
    • For Sale
  • Moderator Section
    • Moderator Back Room

Product Groups

  • Vendor Forum
  • Membership Subscriptions
  • Forum Ads

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


About Me

Found 5 results

  1. I plan on installing the MakeMhz HD+ native digital mod in my 1.6. The only thing I'm concerned with is the AV port which has large solder joints. They remind me of the power jack on my laptop that I tried to replace but was unable to with my soldering iron because the solder had a higher melting point than the 450 celcius my iron is supposedly rated for. Should 450C be good for the entire job?
  2. https://www.youtube.com/watch?v=1N4Oes8MeRA Very good and useful video about how to remove the Xbox's disc tray bezel/faceplate but at between 30 - 45 secs the guys says: "........................... you're going to think you've broken it but you didn't" or words to that affect, repeated several times. Well..............................................guess what: I tried this with the spare dead disk drive and thought I'd broken it.............................and I had. The shower of black plastic pieces was a good indication. What broke were both the retaining channels each end which slide down over the edge of the tray front not the locking tabs as you might think. I believe I understand what went wrong; when I pulled the tabs clear of the bottom edge of the tray I continued twisting the bezel just that little bit too much. What you should do is when the tabs are just clear of the bottom of the tray stop pulling out/twisting up the bezel any more and change to pushing it straight upwards to slide it off the tray. Once the tabs are clear of the bottom edge of the tray and you start to push up they are actually lodged against the flat tray front surface behind the bezel and from that point all you're doing is sliding it up and off. No more twisting or pulling out is necessary. The little crack you may here is, or should just be, the bezel pinging back into shape as it is under tension. If that is accompanied by a small shower of plastic then you've done it wrong. In short: you do need a bit of firm physical persuasion initially but after that be gentle. Bezels do break.
  3. Hi all, I have recently got into the modding scene and after some successful Wii mods have decided to turn my hand at the OG Xbox. I had one of these when I was a kid with a chip on it (don't know to much info as was a kid). I recently picked up 2nd hand Crystal OG Xbox's. One of them already has been softmodded and the other is a virgin, never had the lid popped. I am aware that the clock capacitor needs removing off of all motherboards rev. 1.1-.1.5 however, I have read places that you can cause the system to boot loop if not done correctly. My question is, I have a virgin, a softmod and a chip. Which of these is is safe to remove the capacitor from without getting into a bootloop? I am also finding the most up to date software and guides/information hard to find as there is information floating around from over 10years ago so hoping someone can push me in the right direction with dashboards and other ""basic info" on the latests and most supported software that would be a god send. Many thanks
  4. Dear All, I want to unplug or remove the DVD from my XBOX What is the most convenient way to do this, do you remove the DVD player from the box leaving a tray open for better air flow and afterwards how do you cover the opening, or just unplug the IDE + Power cable and leave the DVD on the box. As the combination of FTP and larger HDD, the DVD Player gets completely obsoleted. Thanks
  5. I’m new to the modding scene, and I’m not an electronics wizard or software genius. I have a 1.1 and I keep seeing that I should absolutely move the clock capacitor. I have looked into why, and I guess it has a tendency to leak all over the MB? Can somebody clarify this for me? (This is the best spot I thought to post this due to motherboard alteration)

Board Life Status


Board startup date: April 23, 2017 12:45:48
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.