Xbox console revision 1.0 in good condition with the following specs:
TSOP flashed
2TB SATA hdd
Digitus SATA -> IDE adapter
80pin IDE ribbon cable
On the HDD is the excellent full Arcadepunks XBMC Origins frontend!
Here is a video they made to demonstrate it: https://www.youtube.com/watch?v=XirumHggTqc
The unit has been fully cleaned, no noisy fan's or bad capictors.
The DVD drive is serviced and fully working.
The power supply is 220volt
Picture gallery with images of the Xbox running: https://jiggmaster.synology.me:5008/mo/sharing/5a0ZhM9jY
Item located in Sweden, shipping worldwide
Price = €100 excl. shipping
Hi, I am just wondering if anyone with more experience than me can tell me how bad this looks or about any diagnosis clues I can be aware of. The first XBOX I found on ebay last year was surprisingly not modded and I guessed it might be a 1.0. Because of that I didn't want to mod it or open it so I bought another cheap one that had already been opened. I had some fun with that one then I gave it away. In the meantime that 1.0 was calling my name and I bit the bullet and opened it up. Softmod went fine of course. HDD upgrade went fine. Then I wanted to try something more interesting. I looked up the RAM upgrade and it didn't look too bad. That actually went smooth. Luckily the 1.0 is the least work to short circuit the TSOP. So TSOP flash and 128MB RAM was working. I kind of surprised myself. I was fumbling around not really thinking through things and I wanted to see if I could flash an original BIOS back to it. That was the end of the fun for me. After the flash it reboots and goes into the blinking red. I realized the BIOS probably didn't like having 128MB RAM so I used my heat gut to remove my just added RAM. That wasn't it. I knew it I had a big project ahead of me. That was when I found the Open Xenium modchip that apparently is supposed to divert the boot to it's own BIOS. Hence my question in this forum.
I didn't see how I was going to remove all that solder from the LPC ports with a solder braid or any other way for that matter. I realized I might be able to use my heat gun again. I had some bad luck and didn't realize how hot I was getting my board in the process either. I almost lost 3 components all together but I managed to get 2 of them back on. I circled the remaining problems in my pictures below. Is any of this repairable? The Open Xenium chip makes it to a red LED but XBOX still only boots to the blinking red lights. I was pretty happy with my soldering of the wire but not so happy with my soldering of the LPC jumpers. The board took some damage. From what the pictures say is this beyond repair? If the Open Xenium chip is making it to a red LED am I close?
Thanks all you smart folks!
Hello people. Finally ive found a forum. Ive just dug my xbox out. Now my question
I run the xecuter 3 mod chip with custom front panel. As far as i no if u hold white button on the controller u can get into the settings menu (fan speed colours bla bla)
All i want to no is. When i upgrade to the new hard drive. Will i have this option again to bring up the menu (white button on controller) or will i have to install it to the new hard drive. Its beem like 15 years since i last used it.
Any help guys
Recommended Posts
Similar Content
TSOP flashed
2TB SATA hdd
Digitus SATA -> IDE adapter
80pin IDE ribbon cable
On the HDD is the excellent full Arcadepunks XBMC Origins frontend!
Here is a video they made to demonstrate it: https://www.youtube.com/watch?v=XirumHggTqc
The unit has been fully cleaned, no noisy fan's or bad capictors.
The DVD drive is serviced and fully working.
The power supply is 220volt
Picture gallery with images of the Xbox running: https://jiggmaster.synology.me:5008/mo/sharing/5a0ZhM9jY
Item located in Sweden, shipping worldwide
Price = €100 excl. shipping
I didn't see how I was going to remove all that solder from the LPC ports with a solder braid or any other way for that matter. I realized I might be able to use my heat gun again. I had some bad luck and didn't realize how hot I was getting my board in the process either. I almost lost 3 components all together but I managed to get 2 of them back on. I circled the remaining problems in my pictures below. Is any of this repairable? The Open Xenium chip makes it to a red LED but XBOX still only boots to the blinking red lights. I was pretty happy with my soldering of the wire but not so happy with my soldering of the LPC jumpers. The board took some damage. From what the pictures say is this beyond repair? If the Open Xenium chip is making it to a red LED am I close?
Thanks all you smart folks!
I run the xecuter 3 mod chip with custom front panel. As far as i no if u hold white button on the controller u can get into the settings menu (fan speed colours bla bla)
All i want to no is. When i upgrade to the new hard drive. Will i have this option again to bring up the menu (white button on controller) or will i have to install it to the new hard drive. Its beem like 15 years since i last used it.
Any help guys
Board Life Status
Board startup date: April 23, 2017 12:45:48