MadMartigan Posted January 13 Report Share Posted January 13 On 12/6/2023 at 2:27 AM, DARK A said: i like thank everyone helped me with the info i convert it and it worked in 220 btw its ver 1.0 i did it by removing jumper wire infront of the left capacitor and the yellow transister right to right cap and it worked i measured the temp of the caps they have no heat problem but the iron thing with warning label after shutting it down it reached 41c should i be concerned or is it normal and what its called is it voltage regulator ? Can you share what all you did? I’m desperately looking everywhere on info the convert the other way around (220-110). All I’m getting is dead ends. Quote Link to comment Share on other sites More sharing options...
DARK A Posted January 16 Report Share Posted January 16 On 1/13/2024 at 8:11 PM, MadMartigan said: Can you share what all you did? I’m desperately looking everywhere on info the convert the other way around (220-110). All I’m getting is dead ends. which version do you have ? Quote Link to comment Share on other sites More sharing options...
MadMartigan Posted January 16 Report Share Posted January 16 All of them. Looking for info on any and all. Quote Link to comment Share on other sites More sharing options...
mado Posted March 15 Report Share Posted March 15 On 1/14/2020 at 11:29 AM, cryptblood1986 said: I actually managed to convert all Xbox PSU to 220v just picture your PSU. I'll give you the schematic. how can you do that? Quote Link to comment Share on other sites More sharing options...
MadMartigan Posted March 15 Report Share Posted March 15 I tried a few months ago to delve into this topic and it seems there isn't much documentation on the subject. Lots of ppl say it's possible but nobody seems to have instructions. Quote Link to comment Share on other sites More sharing options...
MadMartigan Posted March 17 Report Share Posted March 17 @DARK A you left us hanging on the conversion information. Any chance you can provide a guide or help walk us through the process so we can make a user guide for others? This can help so many users. 1 1 Quote Link to comment Share on other sites More sharing options...
Dueiriel Posted April 15 Report Share Posted April 15 (edited) I'm not that technical but I followed what was on these images and it worked great. https://imgur.com/a/0OkmO12 My power supply is the last one, 2 capacitor with checks for 110v and 220v on the board. Changed from 110v to 220v. You could do a guide with the "Just do this" and hope that someone will fill up the technical knowledge haha. Edited April 15 by Dueiriel Switched up the languages haha Quote Link to comment Share on other sites More sharing options...
MadMartigan Posted April 15 Report Share Posted April 15 Unfortunately, I’m needing to convert down to 110V. There is a lot more info on converting to 220v than stepping it down. Quote Link to comment Share on other sites More sharing options...
Dueiriel Posted April 15 Report Share Posted April 15 I think that you only need to solder the bridge that changes the power supply to 110v, I'm not sure if you would need to change the capacitor(since it would already supports the 110v voltage) 1 Quote Link to comment Share on other sites More sharing options...
MadMartigan Posted April 15 Report Share Posted April 15 I may give that shot since I can't find any concrete information. I really don't want to bork a psu or even worse, an entire motherboard. Thanks for the input Quote Link to comment Share on other sites More sharing options...
lopenator Posted April 16 Report Share Posted April 16 I have 2 PAL PSUs that I cannot use because I'm in USA. Wish I could convert them. Quote Link to comment Share on other sites More sharing options...
Dueiriel Posted April 16 Report Share Posted April 16 Which models exactly ? From all the research I did, it boils down to the bridge that changes the psu mode. And the appropriate capacitor to not die to the new voltage. (When changing 110v to 220v). And to maybe bring back the Z1 Varistor, unfortunately I threw mine in the trash, so I'm not able to send the specs here. But if you have a power strip with surge protection, you should be safe. Quote Link to comment Share on other sites More sharing options...
DARK A Posted April 21 Report Share Posted April 21 On 3/17/2024 at 7:23 PM, MadMartigan said: @DARK A you left us hanging on the conversion information. Any chance you can provide a guide or help walk us through the process so we can make a user guide for others? This can help so many users. sorry for the late replay the only version i try it on was v1 and i only followed ss_dave info all i did was removing the jumper wire infront of the left capacitor and the yellow transister right to right cap and it worked btw im not electraion so responsible for any damge that it may cause i only followed dave info here is the picture of the same psu v1 for both pal and ntsc and what to remove but be careful https://imgur.com/a/g5nWjqw Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.