Search the Community
Showing results for tags 'diagram'.
Found 3 results
Took me 2 days to get all the wiring right. for the wii2hdmi for og xbox modd ... using a wii2hdmi device ordered off eBay you can also find an Alibaba and other places like this. Very inexpensive around 5 Canadian dollars. You're also going to need some sort of a donor Xbox RCA wires or component wires in order to pull this off. There is 11 connections total five of which are ground I do not suggest not adding all the ground cuz could cause interference. Had pretty good luck I made to both of them are crystal clear with no interference. I tested on version 1.0 as well as version 1.4 turned out very good. I tried to look up and down online for some sort of schematic nothing appeared. There was one picture that was in Spanish but it was misleading I tried to look into it to find out who the original inventor was found the person at XB Classics a Brazilian site. After conversating with him he told me that he had better pictures but he would not share. Then I noticed a site that they has linked where they were selling these to the equivalent of 40 US dollars a piece so that is the reason the images that they uploaded are just there to confuse people. So that they cannot make it. Does not include audio left or right. And apparently La stands for 5 V? Don't ask me but that's what the guy told me makes no sense at all. I spent two days getting the wiring correct. I documented everything and put it on a YouTube video (link2come) was trying to figure out the best way to make this readily available for everybody in the world any Xbox Enthusiast should have a low cost HDMI adapter solution available to them this is where these schematics come in. Again I didn't notice any interference at all. Just a little bit in the Bios when only running 480 but there's not much you can do unless you re Flash the BIOS to force. I've noticed people in the group posting pictures not even having soldering skills and getting very good results from this method. In theory you can use this exact same adapter in order to have an internal HDMI solution. These images are water marked because these are going to be the only good images that are online and I seen the way XB classic does their water mark and it really bugs me that they did that so I wanted to make sure that everyone knows where it came from. That being said I'm Mister James Reid really helped me out with this he volunteered his services in order to take my hard copy drawings that were on paper and make it look something presentable. Which he did and he did a great job thank you very much James I did in fact alter the images to have the watermark across them. Sorry about that but I figured since I put in the work I deserve to have my name on it. If you have any questions please do not hesitate I do not check this site every day but I do come in from time to time. Thanks again and I hope people online can use this receive money from the big corporations like pounds and hyperkin charging ridiculous amounts of money for something so cheap... I've also got a lot of questions recently about people asking if this is any better than component. It uses the component wires in order to transfer the signal into HDMI. I'm not too technical with that end but when looking up the chip number on the actual board for the Wii to HDMI adapter I did notice in there schematics and their breakdown for the actual board they did mention that the video board that does the decoding actually does video on hand splint what kind of video enhancement I have no idea. But it should be an enhancement over component if they are speaking the truth. Anyway gentleman without further delay here are the schematics. I hope this hope somebody somewhere. Thank you very much Frank
Hey guys, I was reading barnitos LPC diagnostic thread to fix my xbox (still working on it) and i noticed that the baldbouncer image's is incredibly difficult to read and see what pins he is pointing too. I decided to try and update it with a higher-res photo and color coordinate the pins the the corresponding contact hole but I need someone to double check (preferably someone who has done this before) to make sure I'm pointing to the right ones. Can anyone confirm that I've got the Pin #7 going to the right contact hole and that the contact hole for Pin #4 is the proper one? Thank you.
Came across a beautiful selection of wiring diagrams for a bunch of commonly found mod chips. These images are in high-quality HD very easy to read can be downloaded and zoomed in to read perfectly. I am not the Creator of these pictures. The Creator is YouTube channel techno on top. This person normally does Xbox mods on YouTube. There's a video where he shows each of these pictures for 1 minute. I merely took a screenshot of each. Thought it would help out the community here. In any event I hope somebody could use these images. Please pass them around and enjoy Wiring Diagram More common Hardmod Chips.7z
Board Life Status
Board startup date: April 23, 2017 12:45:48