Search the Community

I have an original xbox and I'm wanting to 3D a whole new case. I've seen some stl files but I haven't seen any with a full replaceable case. To where I can take the guts of my original XBOX and add them to the 3D printed case. On a different note how do I tell the version of my Xbox and if the Clock Capacitor needs to be replaced? Thanks in advance.

Hi. I have been trying to find a solution for this issue. This Xbox 1.6 stopped showing the components red color one day, few days later it stopped powering up too. I managed to replace a transistor and it is turning on now, but the problem with the red color persists. The composite out outputs all the colors. The Red pins on the AV port have continuity, but the pin 19 is shorter in length than the rest of the pins and I don’t know If that is intended to be like that or it is damaged or deformed. Does someone know where the problem might be coming from?

I was given Two OG XBOX PSUs but both have 2 missing components One PSU is Delta and belongs to OG Xbox 1.4 revision One PSU is Delta and belongs to OG Xbox 1.6 revision Fuse and varistor are missing in the PSUs, parts are not in the board, someone removed them. i think the owners connected them to 220v (here we have 220v , not 110v in the wall plug) and that caused the fuse to blow up, and varistor to blow up. Just like in the Wii power brick when connected to 220v So i spent some hours trying to figure out what the original components were for those PSUs, searching on forums and i was not able to find the complete info This is what i found online for each OG xbox model, in terms of original components it came with: OG Xbox 1.4 Power supply Varistor= Unknown? I was not able to find information online about this varistor. Fuse: 250v 3.15A (8.35x7.7mm) - OG Xbox 1.6 Power supply varistor: TVR 20241X Fuse : 250v 4A 20mm long - Maybe someone here on reddit knows more about these missing components so Here are my questions for OG Xbox 1.6 revision: The FUSE for OG xbox 1.6 revision, the PCB has printed "250v 4 Amps", and By looking at pictures on ebay i see they originally used a normal Glass Fuse 20mm long, but my question is: DOES IT NEED TO BE A FAST BLOW FUSE? OR SLOW BLOW FUSE? The VARISTOR for OG xbox 1.6 revision is TVR 20241X, but here that part is hard to find, can i use any of these as replacement? S20K150 or 20N241K or 20D241K ? (datasheets images are below) Here are my questions for OG Xbox 1.4 revision: The FUSE for the OG xbox 1.4 revision, the PCB has printed "250v 3.15 Amps", and by looking at pictures on ebay i see they originally used a circle encapsulated in plastic fuse, but again my question is: DOES IT NEED TO BE A FAST BLOW FUSE? OR SLOW BLOW FUSE? The VARISTOR for OG xbox 1.4 revision is UNKNOWN, I was not able to find online what type of varistor they used in that PSU, can i use the same varistor as in the 1.6 revision? here are images of the 1.4 fuse, along with what i was able to find available where i live for the 1.6 revision varistor, I hope someone can help me find the correct replacements

Hi I've got another dead xbox the mobo is corroded by the clock cap. The previous owner tried to repair but components flaked off. I'm hoping I can add the missing components and get it working again with some help here. It's bad. It looks like 5 SMD transistors and 5 resistor or diodes are missing. serial and gfx chip (focus) suggest board is v1.4 according to https://www.informit.com/articles/article.aspx?p=367210&seqNum=2 The same area on v1.6 is very different so it would be a big help if anyone can photo the components on a v1.0 to 1.4 board thanks

Hi I am after a full list of every component that soldered to the Xbox motherboard, all revisions. Caps are well covered high voltage transistors I can find a little yet nothing on resistors and other assorted ICs. If any one has a full list or any list I then may be able to compile a list myself. Thanks in advance for any help

Hi I bought a classic Xbox that has a power problem. The seller told me he had mistakenly connected the console to a 220V source. the type of PSU is Foxlink 1-row. Unfortunately, 4 pieces on the power board are apparently damaged, and I do not know the name and capacity of the two electronic pieces. Also, I could not recognize the value of a resistance due to the color change. I put some pictures of these pieces .If possible, please guide me to identify these pieces. Thanks