Jump to content
OGXbox.com

retroMCR

Members
  • Posts

    16
  • Joined

  • Last visited

  • Days Won

    1

retroMCR last won the day on November 12 2024

retroMCR had the most liked content!

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

retroMCR's Achievements

Newbie

Newbie (1/14)

  • First Post
  • Collaborator Rare
  • Conversation Starter
  • Week One Done
  • One Month Later

Recent Badges

4

Reputation

  1. So, someone in reddit told me to open up the console and apply heat to the capacitors near de AV port with a hair dryer and try after that. So I did that and now the audio output is much better, so I guess the xbox needs a recap
  2. Hi all, I have a TSOP modded Xbox that was sitting in the closet for months. Connected it today to a CRT using component cables and the audio output was very low (on the startup sequence, on xbmc4gamers and on games). I went to the original dashboard to the audio settings, the audio mode was set to Dolby Surround. Also, Dolby Digital and DTS were enabled in the audio settings. I disable Dolby Digital and DTS and set the audio mode to stereo since it is a CRT TV, but the audio is still very low. I tried with another xbox on the same crt and same cables and the audio for that one is ok anyone have this issue before? What can I do to fix this?
  3. In that case I suppose that would be your eeprom. Is your xbox softmodded or hardmodded or tsop?
  4. The password is: A , Y, B, X . Then press start
  5. well, I tried using the monster component cables and before going to the gentoox screen, the screen went black lights flashing red and orange and the disc drive ejected.. looking online I saw this: that was my problem too, used the regular av cables and I was able to flash. Maybe because is a 1.4 xbox? those have different video chips. maybe a compatibility issue with 1.4 consoles.
  6. No, it will not brick your xbox. after the 5 sec it will ask you to insert a boot disc and close the dvd drive. you can just turn off and on the console to start again. Make sure you are not using a component coble to flash a winbond, you will get a black screen. use regular av cables.
  7. Hi Everyone, As the title says, how can I set xbmc4gamers as my dashboard on a TSOP xbox. current dash is unleashx. Thanks,
  8. Now another issue, G partition is showing as 0 MB free, see image below. https://image.ibb.co/ets1RU/20180814_180700.jpg https://image.ibb.co/cqBvmU/20180814_183605.jpg https://image.ibb.co/cVJKD9/20180814_184029.jpg
  9. sorry guys it was my mistake. it is working now. The IDE cable was incorrectly connected, (upside down)
  10. Well, I just got the startech adapter and is doing the same thing.. don't know what to do. Could this be a bad 80 wire cable? Adapter: https://www.amazon.com/gp/product/B00EOJNGC2/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1 HDD I'm using: https://www.newegg.com/Product/Product.aspx?Item=N82E16822235013 80 wire cable https://www.amazon.com/gp/product/B000I21Y28/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1
  11. Thanks, I also noticed that the power indicator LED on the adapter is not turning on . The adapter is defective. But yeah when I put the old HDD and original 40 wire cable the console turn on like normal.
  12. Thanks for the advice,Ordered a startech from amazon

Board Life Status


Board startup date: April 23, 2017 12:45:48
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.