Hazeno

V2.01 is out to fix some bugs

https://discord.gg/4VR8K8mN Xbox Scene has a room dedicated to them. You can post requests for them to see in the cerbios-requests channel. They seem to be pretty active, and it's nice to have a little insight on their plan of action.

That's exactly what I was looking for in the first place! How did you find that archived post lol. I'll get to work. Thanks KaosEngineer for saving my ass again!

Yes it will, but I have no access to the power button or eject button as they don't work when connected. As soon as power is connected it boots. Which leads me to believe it's usually a soldering issue. But all points look nice, ibe reflowed them and tested the chip in another xbox to verify it works. It's actually how I flashed the 1.6 BIOS to bank 2. It now boots to black screen, but that's down to softmod files, but it won't turn off due to the front panel issue. ( Which works fine without D0 / Chip )

Ok guys got an issue that is getting on my wick. Slapped a 2.3b Lite into a 1.6, used a clone LPC Rebuild Kit and proceeded to boot the console. D0 was connected to the board and ground was connected to the screw hole as usual. As soon as you put power to the console it will boot up then reset 2 times before FRAGGING. Only when D0 is connected and chip is off. With chip on with M8 1.6 Bios I can get a boot with Evo shield but it hangs after that and still turns on as soon as a power cord is plugged in. Front panel doesn't work at all. Remove the chip or D0, and it'll boot fine to the original softmod it came from. I've reworked it with my iron, even given it a hot air rework. Which point is most likely the culprit? Apologies on the lead free solder. Was using a friends over my own.

Just need some install diagrams now lul.

Evening all i've got 2 2.3b Lites and one 2.6. Anybody got the install diagrams as I can't seem to find them only the 2.3b+. Also with my LPC Rebuild kit they should work for 1.6's as long as I flash a working bios / Cromwell before installing? As I've ran out of Aladdins and have a few consoles in need of work.

Looking for a new case for 2 of my consoles. Any Colour XCM Case Halo Console shell. UK based preferred

Ok guys I've spoke to chaos engineer about this on Reddit a few times now and he guided me the easiest way to fix but it's now troubling me as to WHY it's occuring as it's never before now? Chip 1 and 2 Ones a 2.3b Lite With markings the other is a 2.3b Without ANY markings. 'Will update with Pics later'. Now I can make a 1mb BIOS with x2 5035 and M8Plus and switch between the 2 using the PCBs fine. But when hexen / skaters flashes it only creates 1 BIOS across both banks my guess here is hexen is creating a 1mb and flashing all 4 banks? I've done everything a normal install would do. Boot on bank 1 - Flash Bank 1 with Bios A. BOOT on bank 1 - Switch while on rhen flash bank 2 with BIOS B.. BOOT on bank 1 - Flash with BIOS A Boot on Bank 2 - Flash with BIOS B Each of these methods BOTH leaves whatever was the last bios flashed as the bios on both banks. Bear in mind the switches work FINE IF I make my own bios and flash within EVOX. Also Ind Bios no matter which struggles with these chips with stuttering which can't be changed or helped even with config changes. Yet M8Plus boots so fast it's actually shocking. Especially since both are SATA with 2TB hdd's. One using Startechs adapter one using a VBEXY? and yes I've switched adapters. I've switched 80 pin IDE cables. (ASUS one required 0 mods actually happy even though it's only 18 inches. What's the best course of action. Flash x2 5035 and M8 Plus 67 manually and leave? Both need f:127 g: Enabled IIRC.

Ok guys I've spoke to chaos engineer about this on Reddit a few times now and he guided me the easiest way to fix but it's now troubling me as to WHY it's occuring as it's never before now? Chip 1 and 2 Ones a 2.3b Lite With markings the other is a 2.3b Without ANY markings. 'Will update with Pics later'. Now I can make a 1mb BIOS with x2 5035 and M8Plus and switch between the 2 using the PCBs fine. But when hexen / skaters flashes it only creates 1 BIOS across both banks my guess here is hexen is creating a 1mb and flashing all 4 banks? I've done everything a normal install would do. Boot on bank 1 - Flash Bank 1 with Bios A. BOOT on bank 1 - Switch while on rhen flash bank 2 with BIOS B.. BOOT on bank 1 - Flash with BIOS A Boot on Bank 2 - Flash with BIOS B Each of these methods BOTH leaves whatever was the last bios flashed as the bios on both banks. Bear in mind the switches work FINE IF I make my own bios and flash within EVOX. Also Ind Bios no matter which struggles with these chips with stuttering which can't be changed or helped even with config changes. Yet M8Plus boots so fast it's actually shocking. Especially since both are SATA with 2TB hdd's. One using Startechs adapter one using a VBEXY? and yes I've switched adapters. I've switched 80 pin IDE cables. (ASUS one required 0 mods actually happy even though it's only 18 inches. What's the best course of action. Flash x2 5035 and M8 Plus 67 manually and leave? Both need f:127 g: Enabled IIRC.