Nf Given XD
-
Posts
50 -
Joined
-
Last visited
Content Type
Profiles
Forums
Calendar
Store
Everything posted by Nf Given XD
-
Yea works fine runs unsigned code I've used it since I bought it no issues just can't flash
-
https://www.dropbox.com/s/dlp7of6hg8vetx5/side2.jpg?dl=0 https://www.dropbox.com/s/iu07aube3n1ldmh/side 1.jpg?dl=0 https://www.dropbox.com/s/uxjhpmoma6xofrr/Lattice chip.jpg?dl=0
-
Flash BIOS Manufacturers ID 09 Device ID 00 !!Unknown Flash Type!! Thats what I get when trying to flash
-
would i have to alter the chip solder points or just flash it with hexen?
-
Hey ss dave mind helping me "for dummies" on flashing a aladdin v2 with a 1.6....I read a recent post and im not 100% on it ...so just wanting to make sure it wouldn't be a bother to ask if it goes bad.... As im thinking about using cerbios
-
Has anyone tested different cat cables ie cat4 vs say cat8? If so is there issues with using one vs the other?
-
It um.....it just works....I was prodding around with the meter saw a spark on testing the video chip....turned it off...cleaned it up with ipa....and now it seems fine
-
Spoke too soon anyone got a diagram of the lines and power supposed to be on it?got a multimeter to test it since everything is failing to fix it.
-
Tysm ss dave and the rest that were so reluctant to help me ...the psu was the whole problem.question though...is the bios unknown in 1.6 a good thing?ie because I cut the trace? See og post for latest TLDR : PSU or Power Supply Units can cause frag with simular issues to overheating/rotted traces/blown caps however id never suggest to replace a PSU without having these wonderful members take a look at it :). thank you all.
-
Thank you for your reply will try and hope it dont melt anything else lol I'm gonna buy another one just in case but money was tight last week but paydays tomorrow
-
Top https://www.dropbox.com/s/5ss0xyk07m5dw1d/img_20220111_134834.jpg?dl=0 Bottom https://www.dropbox.com/s/fkkde2fw9i1bxw7/img_20220111_134852.jpg?dl=0 Disregard the dirt tossed it in a junk drawer when it fried
-
How do I get my original hard drive back to stock configuration?
Nf Given XD replied to roybridge's topic in Repair
If its chipped id suggest a recovery disk maybe hexen 2021 . -
Is it normal to have a 1.6 board ran by a Tuscany psu?I could have sworn i read somewhere Tuscany was 1.5 only. Also....I believe the psu was in fact the issue....question...could a jumper fix a melted trace pad on the psu?
-
Power supply died so wont be working on it for a lil bit till I can grab another
-
If I don't mind the led being on I just don't cut the trace?and the black line is what exactly on the chip trying to fully understand... Wait so thats efficiently turning the led on and off with system power...gotcha Lastly without pin 4 and 6 the chip doesn't light at all on or off...and the power issue <frag> still persists albeit takes a little longer then frags over and over....maybe worth noting after it sits a while it attempts<attempts being it will boot for a while THEN frag> full boot again....if that helps
-
So pulled those two out and it didn't boot the chip im assuming cause I desoldered D0 in the previous attempt to fix it however once I get off tonight <in 9 hours> ill resolder D0 and see if that changes it as it didn't full power cycle this time.
-
Any way I could get a marked pinout for the pin header?not 100% on pin numbering as I didnt see it on the guide I used
-
Hey Dave I wanna thank you for all your help it was in fact that capacitor that was causing issues although I cant see damage to it?I'm up and running though thank you for assisting in that. Edit: spoke too soon....ran an hour then frag...last thing I'm trying is new paste then if its still bugged im trashing the board and starting over as I cant seem to pinpoint the issue ...so hopefully its a heat issue.
-
Yes it shows it and boots hexen but I haven't tried without the disk in ill test it without the disk but I assume its gonna error out as I havent had the chance to null the eeprom <update> I got it locked to the boards eeprom after formatting and preparing the drive only to be locked on the boot screen with Microsoft to finally after about two mins boot to the green screen. <update update> One of the main caps are busted i cleaned up what looked like dust on the board near a cap and its back so I beleive im waiting for the cap set.pics in link
-
Could this be a bad gpu?
-
yes I cut that trace.also uploaded 2 pics of the new pin solder and boot up after...it booted for a good 5 mins instead of 2 this time but eventually green screened for 3 secs then frag again.<same link as above all three named.>
-
The mounted wire by db7p1 is the d0 correct?not wanting to make assumptions to make sure I got it right this time.
-
Also to note it does the same without disk drive and hdd...so thats why I assumed either install or mobo issues
-
Will look into it soon and try your suggestions on my next day off thank you sir. Also the hexen disk was bought offline from a lad with positive reviews so I wouldn't assume the disk was the culprit.
-
As the title states I have a 1.6 xbox that after lcp rebuild and mod chip install it reads hexen and works for a few mins then frags...I have capacitor and transistor replacements on the way ..but really curious as to what could be causing it photos will follow. https://www.dropbox.com/sh/xgfbhusv4f6h2ff/AAAotnIs2jHOwIA_JFidW-Iba?dl=0
Board Life Status
Board startup date: April 23, 2017 12:45:48