Jump to content

Search the Community

Showing results for tags 'transforming '.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Off Topic
    • New Member Introductions
    • Rumble Pit
    • Suggestion Box.
  • General Xbox Discussion
    • General Xbox Discussion
  • Original Xbox Modding Forum
    • Hardware Mods
    • Modchips
    • TSOP Flashing
    • Softmods
    • Repair
  • Xbox Case Modding
    • Case Mods
    • Lighting & Electrical Mods
  • Tutorials
    • Official Tutorials
    • Tutorial Submission
  • Software
    • Bios
    • Dashboards
    • Installation Disks
    • Applications
    • Games
    • Emulators
    • Homebrew
  • Xbox Collecting
    • Xbox Collection Showcase
  • Rare and Uncommon
    • Rare and Uncommon Xbox Hardware
    • Rare and Uncommon Xbox Software
  • Vendors
    • N64 Freak's Products
    • Barnito's Products
  • Development
    • Rocky5's Projects
  • Online Play
    • Game Night
  • Classifieds
    • Wanted
    • For Sale
  • Moderator Section
    • Moderator Back Room

Product Groups

  • Vendor Forum
  • Membership Subscriptions
  • Forum Ads

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


About Me

Found 1 result

  1. Ever wanted to add a new D-pad to your controller? Probably not. But im still gonna show you how. Both methods are on an S-Controller. I haven't tested on a Duke or any other controller. If you wanna try then let me know how it goes. Tools/Materials You'll need for this mod Phillips Head screw driver mini Phillips head screw driver Regular D-pad from an xbox 360 Controller or A Transforming D-pad from a 360 Controller (Depending on which mod you wanna do) Needle Nose pliers or Wire cutters(For method 1) Dremel/Rotory tool Sanding Barrel and cutting disc for your Dremel. and 10-15 minutes of your time. PART A: Disassembly First you'll need to pull apart your controller. there are 7 Phillips head screws on the bottom, 1 is under the barcode sticker in the center. once removed you can pull the bottom part up and remove the internals. Once you have everything stripped from the top half of your shell you'll need your Mini Phillips head screw driver. remove the 2 screws holding your original d-pad in place and pop it out. Part B: Mod Method 1 Now take your new 360 d-pad and look at it . the one on the left is the original S D-pad. right is from the 360. You'll want to remove the locating tab on the right side using your cutting disc. Alternatively you can snap it off with a pair of needle nose pliers or even some wire cutters. Now pop it in and reassemble everything. Your done!! This mod isnt really for the Original colored D-pads (Grey or Black) But once done you can buy many different colored ones for the 360 controller. Great if you plan on painting your controller. Part C: Mod Method 2 First you'll need to pull apart your controller (Refer to Part A) Once taken apart you'll need to take your Dremel with the sanding barrel and remove the internal part of the d-pad mounting location. Go slow and take your time. Don't cut any deeper than whats in the picture. If you cut too deep you will ruin the controller. all you wanna do is cut/sand it down smooth to the cylinder wall.(If that makes sense) Now you'll need to flip your controller over, and put the new D-pad into place. You'll notice the locating pins are preventing it from going in. You'll want to take your cutting disc and cut notches in the Controller so the D-pad can go in. (I cut to vertical slices and then used my screw driver to snap the piece off) Not the cleanest way to do it, but it works. Once the notches are cut you should be able to put everything back together (Using the original Rubber insert for the d-pad) and you are done!! Enjoy your new Transforming D-Pad!

Board Life Status


Board startup date: April 23, 2017 12:45:48
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.