Search the Community

Requirements: Single CAT5 ethernet cable. PC with an ethernet port. Xbox console. Configuring the network adapter: Connect one end of the ethernet cable to your Xbox and then the other end on the back of your PC's ethernet port. Go to 'Network and Sharing Centre' and select the first current Wi-Fi connection. Select 'Properties' > 'Sharing' and check the box labelled 'Allow other users to connect through this computer's network'. If there is more than one connection in the drop-down list, then select 'Ethernet' and click 'OK' twice. Next, select the ethernet connection. Select 'Properties', check the box labelled 'Internet Protocol Version 4' then select properties. From the properties window, make the following changes: IP address: 192.168.0.1 Subnet mask: 255.255.255.0 Default gateway: 192.168.0.100 Once you've made the following changes, click "OK" twice. Download WinSCP or FileZilla, any client will do, which will be used to connect to your Xbox. Setting up network configuration on Xbox: (This section will only be focusing on setting up FTP for UnleashX, your dashboard may follow a different setup). From the UnleashX dashboard, select 'Xbox Admin' > 'System' > 'Settings' > 'Network'. Make the following changes in the 'Network' section: Type: Static IP address: 192.168.0.2 Subnet mask: 255.255.255.0 Gateway: 192.168.0.100 DNS 1 & 2: 0.0.0.0 Press 'B' once, when you are asked if you want to make changes to the configuration, select 'Yes'. Go back four times using the 'B' button, then scroll down and select 'Reboot'. Once the system reboots, the new static IP address will show up in the bottom-right corner of the screen. Connecting to your Xbox: To confirm that everything works, open up the FTP client of your choice that you have installed. Enter the IP address of your Xbox, set the port to '21' and click 'Connect' or something similar in your client. When asked for both a username and password, the defaults are 'xbox' (no quotations).

Hi again everyone. Recently, I managed to get my hands on an Aladdin XT Plus2 and install it in my Xbox. All is well right now, but I want to replace unleashX with UIX. Would that be possible? And if so, how would I go about doing it? I've tried Googling to no avail.

I have a TSOPED Xbox PAL console and it is running the 2TB Origins image. I had previously set the the video mode to NTSC and was using the HD resolutions fine no problem with a HD component cable, only trouble was the cable was not good quality and caused a lot of buzzing sound through my speakers. So I bought the Bitfunx HMDI adaptor (think it is similar, if not same as the Pound one). Problem I have now is that I can't seem to use it and display in NTSC HD modes at all. If I set the console to PAL the Xbox shows the EVOX boot screen and then loads the dashboard fine (obviously only in the lowest res PAL mode) If I set the console to NTSC the Xbox shows the EVOX boot screen but then the dashboard won't show as it appears the TV is not receiving a HD signal. I am stuck, is there anything I can try? Thanks in advance.

so i have XBMC4gamers setup to run as an app. the trainers i downloaded from within the dash work fine but how do i add new trainers for games i have i downloaded soem new trainers but idk how to add them so that XBMC4gamers will see them

Sorry if this has been posted before but I needed to know so I thought I'd post here too. 256k Bank Bank 1: on on on on Bank 2: off on on on Bank 3: on off on on Bank 4: off off on on Bank 5: on on off on Bank 6: off on off on Bank 7: on off off on Bank 8: off off off on 512k Bank Bank 12: on on on off Bank 34: off on on off Bank 56: on off on off Bank 78: off off on off 1MB Bank Bank 1234: on on off offBank 5678: off on off off 2MB Bank Bank 12345678: off off off off