Jump to content
OGXbox.com

Onaga

Members
 View Profile  See their activity

  • Posts

    74

  • Joined

  • Last visited

  • Days Won

    4

 Content Type 

Posts posted by Onaga

  1. IP 0.0.0.0 (Set to DHCP)

    in Repair

    Posted

    On 5/26/2022 at 7:53 AM, big F said:

    If you cant get it to work with a manual address assignment, then that might suggest the LAN port has taken a surge wack at some point in its life.  You have done everything else to check.  So its fixable but maybe better to cut and run on that Mobo.

    I put a new Port on the Mobo, still not working.

    On 5/27/2022 at 11:05 AM, Bowlsnapper said:

    Can you get an IP with ANY DHCP setup whatsoever? Is this the only setup youˋve tried to connect with?

    Yes, just the one setup.

  2. IP 0.0.0.0 (Set to DHCP)

    in Repair

    Posted

    17 hours ago, Yoinx said:

    Sorry, slow reply... I got tied up with stuff.

    That's a subnet mask, not a DNS server. From everything else I've seen posted after this comment, the only thing that I can say that I've seen act odd is depending on which dashboard was set to default, my xbox would act weird for IP addressing. Some dashes would get their addresses right, some wouldn't. Then if you launch another dash from that one, it's network would be all screwy and not correct itself. Maybe try re-installing a dash that you *know* should work right and reconfigure it?

    I know on my network, between the OGXbox and the Xbox 360... the have an oddity because I run my network on the 192.168.0.0/16 or 255.255.0.0 subnet (depending on your preference). However, sometimes the units will get an IP address but use the typical 255.255.255.0 subnet, which obviously causes issues. 

    I did try different HDDs and Dashboards, didnt work. They all work in my other consols.

  3. IP 0.0.0.0 (Set to DHCP)

    in Repair

    Posted

    13 hours ago, KaosEngineer said:

    Does the Xbox's Link LED on the Ethernet port light up?  

    Look at the wires inside the jack to make sure they are all present (8), not pressed down and not covered with dirt and grim.  I had one console that they were completely covered. The Ethernet cable could not establish a link since there was no electrical connection being made.  Once cleaned off, the Ethernet port worked again.

    yes it lights up. both colors light up (green/orange).

    as mention in my first post, I took of (desolder) and put a new Ethernet port to the board. Did not help.

    I can't get it to work. I'm going to desolder the RAMs, Caps and HDMI Mod and use another board that works.

    From now on I check if the board gets an IP before I upgrade it with mods.

    Thanks for all the help!

  4. IP 0.0.0.0 (Set to DHCP)

    in Repair

    Posted

    On 5/22/2022 at 7:32 PM, Donnie-Burger said:

    You can also use fatxplorer and never ftp ever again.  Its way faster just need to hook up your drive.  Good luck bud.

    Thanks, I know fatxplorer, but it's more time consuming for me to take the harddrive out of the xbox. FTP seems easier especially for very small data transfar.

    For brand new harddrive I use fatxplorer ect.

    13 hours ago, RetroEmulationNation said:

    I assign a static IP to my Xbox via the original MS Dashboard
    No problems with downloads via XBMC4Gamers or connecting to the console via FTP

    Perhaps you should consider using a static IP?

    Just use ipconfig in your PC to identify what is your router's IP address (I am betting it's 192.168.0.1).

    The rest should be relatively straightforward.

    It's not about me. I have multiple consoles in my collection that work fine. The one we are talking about is for sale and I don't want to sell a consol with problems like this. It should be as user friendly as possible. Xbox, 2TB HDD, 128MB RAM, new Caps, awesome Dashboard, and there we go... pop in LAN cable and play online useing XLink Kai... just as usual.

  9. IP 0.0.0.0 (Set to DHCP)

    in Repair

    Posted

    Yes I use two different setups but they are not connected. For FTP I just use the IP-Router. Xbox gets a static IP and I can easily connect via FlashFXP. There is no other router or modem in between. It’s more like a closed network.

    For XBMC I connect straight to modem and basically get the IP and internet connection. But not for this one, it stays at 0.0.0.0. Never faced that problem before. And I don’t understand it because I didn’t change anything on my setup or installation.

    I’m going to try what you recommend, maybe I get the Xbox to work. It’s still not the ultimate solution for me because I don’t want to keep the Xbox. It’s for sale. 

     

  10. IP 0.0.0.0 (Set to DHCP)

    in Repair

    Posted

    Because it's just an old setup I'm useing almos 20 years now for FTP. Easy and save and I got all the programms on my XP PC... FlashFXP, Eeprom Reader, XISO ect...

    Modem is "Fritzbox 7430", nothing special, I use it all the time and never had any problems.

    It's really strange never faced a problem like this before.

  11. IP 0.0.0.0 (Set to DHCP)

    in Repair

    Posted

    For FTP connection I use a "Allnet ALL1294A Broadband IP-Router" between XBox and PC (Old PC with XP on it).  This is where I get the IP 192.168.0.6. I do it all the time.

    For "Internet/XLink Kai/ XBMC Cloud" I hook up directly to my modem (as I do with all other XBox after TSOP ect.) This is where I get 0.0.0.0.

    Yes, I replaced ICS 1893AF two times on the motherboard (desolder and reinstall new one). I did same for the "Ethernet connector". Didn't help.

    Setup on HDD seems to be fine as well... because it works in every other Xbox I own.

     

  13. IP 0.0.0.0 (Set to DHCP)

    in Repair

    Posted

    It’s not only Kai, I can’t download from xbmc cloud as well.

    Every other Xbox connects without any problems. Same settings for modem and XLink Kai. Same bios, same dashboard, same HDD ect. Basically just different mainboard.

  14. IP 0.0.0.0 (Set to DHCP)

    in Repair

    Posted

    You know how to connect to XLink Kai? No complex setup… just a Xbox with tsop, XBMC4Gamers set to DHCP, lan cable to modem. Basically I get a IP for example 192.168.1.56… but it doesn’t work. It’s just 0.0.0.0. 

    For FTP I get IP. 192.168.0.6. Setup is little different. But that’s not important for me. Important is that I don’t get connection to internet (XLink Kai). I have multiple consoles and they all work. Same setup for all of them (hardware/software). 

    B3EEA7D3-A447-4AC8-A7A2-2DAC05E2D47E.JPG

  15. IP 0.0.0.0 (Set to DHCP)

    in Repair

    Posted

    I have no clue…. For FTP I get IP… but for internet I don’t. I can hook up other consoles at the same time and they work  

    That’s why I’m asking. It’s no joke. Any ideas what to do? Could it be a console that got banned by Microsoft back in the days? 

  16. IP 0.0.0.0 (Set to DHCP)

    in Repair

    Posted · Edited by Onaga

    First time I got no IP on an Xbox Classic!

    Add new Caps, 128MB RAM upgrade and it works totally fine.

    I use XBMC4GAMERS, iND Bios, just same setup as always..., Network is set to DHCP. Can't get an IP!

    Tried two different ethernet ports (ICS 1893AF)... still no IP... 😪

    Any solutions, please??

    Edit:

    -Tried new ethernet connector as well, didn't help...

    - FTP connecton works!!

  18. XBmc4gamers

    in General Xbox Discussion

    Posted

    9 hours ago, KaosEngineer said:

    What info ?

    Edit: Oh the game's title as Rocky5 posted many pages ago.

    It's stored inside the header of the game's default.xbe file.

    For more information, see: .XBE File Format (caustik.com)

    Hey there,

     

    I already saw the instruction, but isn't there a different way to change the titles? I don't want to use the "Controller" for this... I want to take the "File that contains the titles", get it onto my PC via FTP and change it by hand (keyboard).

    Is there a file like this?

  19. XBmc4gamers

    in General Xbox Discussion

    Posted

    On 6/27/2018 at 6:04 PM, Rocky5 said:

    Above answered the first part.

     

    the LED you need to set on your softmod or hacked bios. XBMC doesnt oatch the kernel when changing the LED. UnleashX does just like the softmod or hacked bios does. 

    Hey Roxky,

    which file of XBMC4Gamers contains that info? Because I want to change a lot of titles but I want to use my PC for this.

  21. 1 Ghz and 1.4 Ghz XBox Problem Game(S)

    in Games

    Posted

    You have a benefit in loading time for a lot of games, this is for sure! I made a video where I compare 733Mhz vs 1,4 Ghz and you have 3 sek faster loading time just for "FarCry Evolution"... combine this with a SSD and you get an insane loading speed/boost. Faster loading time stays even if you patch the xbe file, thats awesome!

    You can also see a huge difference if it comes to Ps1 Emulator... as well as picture(video) quality on every other emulatore (way sharper and more colorfull).

    Overall I'm very happy with the 1,4Ghz XBox... took me some hours to make my HDD almost perfect... there are just a few very good game titles that I can't get to work but I can live with that. I mean, I have a stack of modded XBox consols, I don't care if I have to take a regular one to play Call of Duty 4 just because it doesn't work on my 1,4Ghz, haha :)

  22. 1 Ghz and 1.4 Ghz XBox Problem Game(S)

    in Games

    Posted

    1 hour ago, Bowlsnapper said:

    The reduction circuit doesn't actually reduce the clock speed, so you wont see an application report that. It somehow kills every other cycle to achieve half performance. I wish i understood how. However, if supposedly reducing performance to 733mhz (stock) eqivalent speed doesn't enable compatability with timing-sensitive games, then I'm not sure what the flying fuck its practical purpose actually is.

    I wish somebody would be willing to explain why OG xbox games are set up in a way that causes them to vary in speed depending on clockspeed and PC games are not. PC games just vary in performance/framerates.

    WTF? Why?

    I don't understand either... the switch is usless from my experiance, at least for xbox games. Not sure if there is any difference for movies or emulators... but emulators works all fine for me except of "Ninja Massive Pack"... have to use KAWA-X for Neo Geo Games...

    It's really not easy to make all the games work on a 1,4Ghz... some games requier 128MB patch, some not... some require Trusty 1400 patch, some FriendTech... sometimes you have to patch multiple *.xbe files... and some games worked after I patched manually with HxD, for example "Manhunt".

    So far it seems like I can't get 72 out of 761 games to work.

Board Life Status


Board startup date: April 23, 2017 12:45:48
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.

  I accept