-
Posts
88 -
Joined
-
Last visited
Content Type
Profiles
Forums
Calendar
Store
Posts posted by adam hunter
-
-
15 hours ago, KaosEngineer said:
Yes, extract the dot ISO file from the archive, burn that disk image to DVD-R media then boot it in the Xbox.
For a replacement dashboard, I prefer UnleashX.
ok i'm going to do that but how i can us UnleashX
-
1 hour ago, KaosEngineer said:
Which replacement dashboard is the console booting into?
Edit: I see it's not booting into a replacement dashboad. That means the installer of the modchp did not complete the modding process. They did not boot a modified Xbox installer disc to install a replacement dashboard.
Installing Replacement Dashboard, Games and Emulators
Edit: Boot a modified Xbox installer disc such as OGXbox Installer 2021 v1.5.3.d The installer disc is used to install a replacement dashboard to the hard drive.
FTP to the Xbox and upload the files of the games or emulators to the Games or Emulators folder on the E, F or G drives. If those folders don't exist, create them. Each game or emulator goes into a separate subfolder. Each emulator has its own subfolder where you place the ROMs for it.
Xbox Modified BIOS/Kernel Version
Which BIOS / kernel is on the modchip?
Find the kernel version and post it. Most likely you'll see it's 1.0.5838.1 - M8 or M8plus. I'm not exactly sure which version the maker of the Aladdin modchip preflashed to the modchip.
so i mast burn OGXBox Installer 2021 in a dvd then i put it in my xbox right and what is the best dashboard
-
6 hours ago, KaosEngineer said:
For the way your Aladdin XT plus 2 modchip is installed, you have to hold the power button for longer than 1 second to enable the modchip so it will boot the Evox BIOS flahed to it. A short tap of the power button to turn on the console will boot the stock BIOS from the TSOP flash memory chip on the motherboard (or in your case with a v1.6 motherboard the custom Xyclops chip).
I suggest removing the wire connected from the resistor on the front of the motherboard to the BT pad on the back of the modchip then on the opposite side solder a new shorter wire from the BT pad to a ground point as shown below: (Edit: the larger square pad to the right with the trace running from the quick solder pad, pin 2 - ground, works too.)
This mod enables the modchip all the time. Thus, a short or longer power button press will always boot the BIOS flashed to the modchip.
what my xbox is 1.6 but my xbox it's date 3.6.2005 so how it's be 1.6 and i'm not having en experience in soldering so tall me how i can add games and emu in my xbox and how i can chang the dashboard
-
i opened my xbox and i found that i have an Aladdin xt plus 2 modchip i took a photo for it what i can with that modchip and why when i turn on the xbox i see the original dashboard and i din't see that modchip at all what i should do and is my xbox mother board 1.6b or what
-
4 hours ago, SS_Dave said:
It's hard to tell the type of chip as quite a few have a red light but any way as the Xbox is a version 1.6 you really only need to update the bios to the newer EvoxM8 file then give the insides a clean, fit a bigger hard drive install a dash-board and fill it up with games.
You should also check the capacitors next to the heat sink for signs of bulging and if there is an sign of damage replace them.
On the 1.6 xboxs I get here that's about all I do with them.
You could fit a different mod chip with a LCD, 3tb (2.2tb Useable) HDD, Internal HDMI out, Internal OGX360 for using wireless controllers but that's up to you and how much you want to spend.
Cheers
SS Dave
Soft modding is like masturbating, It gets the job done but it's nothing like the real thing.can you tall me how i can get that EvoxM8 file and how i can do an update to the bios should i mast have a memory card how should i mast have an original splinter cell or i can do a copy for it
-
1 hour ago, KaosEngineer said:
The Evox shield displayed on startup is from the Evox BIOS flashed to the modchip.
The Evox BIOS can be flashed to any Xbox modchip.
Without seeing the modchip, you can't tell which one it is since many have a red LED on them.
so how i can add games and emo and how i can change the dashboard
-
7 hours ago, KaosEngineer said:
There is no evox modchip. However, there is an Evox BIOS and the evolutionx (evox) replacement dashboard.
Edit: There is an Xecuter 2 modchip. Post a picture of the modchip so it can be identified.
when i turn my xbox i see that there is a red light i took a movie for the xbox and that red light
-
hello today i started my xbox whom is 1.6b but i found it has evo x modchip can someone told me what is evox modchip is it so good?
-
2 hours ago, SS_Dave said:
Yes you still need to change the capacitors next to the heat sink and remove the clock cap from the version 1.0.
Can you post a pic of the power supply that is in the 1.0.
Cheers
SS Dave
Soft modding is like masturbating, It gets the job done but it's nothing like the real thing.that is the power supply
-
32 minutes ago, SS_Dave said:
Until you replace the capacitor's near the heat sink the Xbox is not going to function correctly..
Cheers
SS Dave
Soft modding is like masturbating, It gets the job done but it's nothing like the real thing.i found out why my xbox not work correctly as i said to u before my xbox is 100-145 watt my country uses 200.240 watt so if i want to turn on my xbox i mast use power convector so i used winstar power converter and my xbox wasn't run perfectly so i used set up and down transformer so my xbox run so smoothly i even took out the hard drive and i turned on the xbox it worked good so and even with the hard drive it works good so should i remove these capacitor
-
15 hours ago, SS_Dave said:
Have you replaced the Caps next to the heat sink?
Cheers
SS Dave
Soft modding is like masturbating, It gets the job done but it's nothing like the real thing.
not yet because i don't have them yet
-
4 hours ago, SS_Dave said:
I would not bother replacing the Clock Cap in the 1.0-1.4 Xbox boards as it is for short time (3 to 5 hours) time retention when the AC is removed.
I have all my Xbox's get the time from the internet when the Xbox dash loads.
Cheers
SS Dave
Soft modding is like masturbating, It gets the job done but it's nothing like the real thing.
i removed the cable of the xbox power supply then i put it back again and turn it again with hard drive but this time it takes few moment then before to turn off is that because of the power supply
-
15 hours ago, KaosEngineer said:
Those bad/leaking capacitors by the CPU heatsink. They have a different case style than the originals but are the same series (HD) / specs as the metal can cased capacitors.
sure i'll buy them but is there a capacitor for clock ?
-
3 hours ago, KaosEngineer said:
Nichicon 1500uF 6.3Vdc ultra-low ESR 105 degree C rated electrolytic capacitor
https://www.mouser.com/datasheet/2/293/e-hd-22785.pdf
https://www.mouser.com/ProductDetail/Nichicon/UHD0J152MPD?qs=4rl4CYS9CJADWZ%2F01acxtg%3D%3D
what is that use for
-
20 hours ago, SS_Dave said:
Yes
If you have not had a lot of soldering experience I would suggest not learning on the Xbox. you should find some old/broken electronics to practice on 1st.
The version 1.0 I see a lot of damage to the LPC port because the holes are already full of solder and people have problems removing the solder without damaging the board and the 1.6 needs some wire links from the LPC port to the main board to make the mod chip work.
Cheers
SS Dave
Soft modding is like masturbating, It gets the job done but it's nothing like the real thing.yeah sure i'll take to someone know how to soldering buy the way today i bought an xbox one can i hack it with mod chip
19 hours ago, KaosEngineer said:Don't see a 1500uF cap in there. Only a few 1000uFs and 330uFs.
do u have photo for it
-
-
5 hours ago, SS_Dave said:
If you want to add a small LCD to the front of the Xbox then the Open Xenium, XeniumIce, Xblast Lite in both the 1.0, 1.6
If you don't care about the LCD then a Aladdin is fine in both.
I would use a Aladdin mod chip in the version 1.6 and reflash the onboard bios of the 1.0 and not worry about the LCD
The 2nd option is a Aladdin in the 1.6 and a Open Xenium with a LCD in the 1.0
Cheers
SS Dave
Soft modding is like masturbating, It gets the job done but it's nothing like the real thing.yes i want to add many things in my both xboxes so i mast take Open Xenium right?
-
ok i will try that but i want to know what is the best mod chip for my xbox 1.0 and my xbox 1.6b
-
you mean if i replace them with new 1500nf 6.3 my xbox will work?
-
13 hours ago, SS_Dave said:
Yes the Xbox will not boot up properly until they have been replaced.
Cheers
SS Dave
Soft modding is like masturbating, It gets the job done but it's nothing like the real thing.but why when i start the xbox without hard it works and when i put the hard it turn off and what are the Capacitors that match for those Capacitors
-
20 hours ago, SS_Dave said:
are they make the problem ?
-
-
6 hours ago, SS_Dave said:
If you do not have a hard dive connected to the Xbox will it stay on (fan spinning)?
Cheers
SS Dave
Soft modding is like masturbating, It gets the job done but it's nothing like the real thing.if i put hard drive the xbox turn off if i remove it work in fan spinning
-
10 hours ago, SS_Dave said:
6 volt should not be there,
What readings do you get with no hard drive and will the Xbox stay on with no hard drive connected.
Cheers
SS Dave
Soft modding is like masturbating, It gets the job done but it's nothing like the real thing.i didn't use it because i don't have i rote the volts on the hard drive
Board Life Status
Board startup date: April 23, 2017 12:45:48
i have an xbox 1.0 what the best modchip for it
in Modchips
Posted · Edited by adam hunter
i installed and burned the iso in an dvd with purple bottom but when i put it in my xbox it said it can't recognize the dvd is there a way to burn it in a cd?