Jump to content
OGXbox.com

Kup

Members
  • Posts

    13
  • Joined

  • Last visited

  • Days Won

    1

Kup last won the day on June 18 2021

Kup had the most liked content!

Kup's Achievements

Newbie

Newbie (1/14)

  • Dedicated Rare
  • Conversation Starter
  • Week One Done
  • One Month Later

Recent Badges

1

Reputation

  1. Hello SS Dave, So pin 2 is reading 4.8v and pin 4 is 3.13v and that is when the console thinks the tray is open. Also connected pins 4 & 7 both before boot & after but the console still says tray open. Its like the drive status has somehow become reversed ? The only time the DVD drive works properly is when a disc is in, and you hard reboot, but so at this point its not reversed ???
  2. Hello SS Dave, The DVD drive is Samsung, The problem persists with the eject button, even when the DVD drive is not connected, so will the above solution help me ? Here is a pic of the top of the board (right click on it and open in new window, then click zoom)
  3. So just swapped to a background picture that displays drive status and....... The dash says ejecting constantly until hard reboot, so if i press eject before dash loads then status = ejecting, or when dash loads and it soft reboots then tray status = ejecting. When the DVD drive is not connected tray status = open, if eject is pressed then system hangs on reboot (maybe because its waiting for the tray to close ?) Is this a hardware fault that can be fixed ?
  4. Morning, so i have tried the config, and unfortunately it doesn't fix the eject problem. So i re flashed a new bios (evoX) and still it reboots on eject, next i tried 2 old HDD's, which where taken from old soft modded Xboxs, before they where upgraded, and they both gave error 13 (something to do with the kernel). Finally found an old blank 80GB HDD and formatted it to stock, then added evoX dash. Still the DVD reboots on eject, if i boot with the tray open, wait for dash to load then press eject the tray will close without reboot, but when pressed again then it reboots.
  5. Hello SS Dave. From the small amount of time i have used it, i have experienced none of the above, not once, it just soft resets when eject it pushed. Its ever so strange and i am hoping that config.ini will fix the problem, thanks for your help and i will let you know tomorrow.
  6. Hello SS Dave. Thanks for the file, its late now and i will have to put the motherboard back in, so i will check in the morning and let you know if it has worked or not.
  7. Hello Mousxaros. It could be that, but the motherboard was amazingly clean, when i removed the clock cap there where no signs of leaking on top of the board. Have taken this pic of the bottom, don't know how well it will zoom, it looks OK to me ?
  8. Hello SS Dave, So the Xbox is resetting when i push eject, and it was doing this i think before it was flashed, can this be disabled ? The bios was X2 5035 - 0xb8f6da5b60f9ac5b775e28e86a493ca0
  9. Hello, Got a v1.1 Xbox today that i wanted to TSOP flash, but it has some issues, before doing anything the console was tested. The hard drive is making some loud whirring sound, but it manages to boot to dash, this will be replaced with a bigger drive. The DVD ROM was locked solid, so after opening the console and the DVD ROM, and giving it a good clean, that is now working again. But when i tested the DVD to see if it ejects, which it does, every eject press the console now appears to soft reboot, i mean it restarts but doesn't power cycle. Anyways i soldered the points on the mobo, and continued to flash which was successful, but the problem still remains with the eject. The console hadn't been opened before today, as far as i remember it didn't reboot on eject when i 1st turned it on to test and was trying to eject the tray. Have tried an alternate power/eject board but no change, also the console boots with no DVD drive connected also with no change, so i am out of ideas. Has anyone experienced this, or know of a fix ? any help is appreciated.
  10. Hello HDShadow, thanks for the reply/confirmation. Have had a few tsop/chipped consoles in the past, and the difference seems to be that, with those the Xbox logo screen hangs until the dash appears, which i prefer over the black screen. Anyways its not really a big problem, was just asking in hope of a possible fix. Once again thanks for the confirmation.
  11. As far as i remember, it was booting correctly, or at least i didn't notice the black screen originally. And i think the hard drive was formatted correctly, all partitions have populated OK, it shows up correctly in Xbox partitioner 3, and everything works and loads from the different partitions, except for this hanging black screen upon boot for around 10 seconds, before the dash loads. Although not the end of the world, everything works and the HDD upgrade went OK, would have been nice not to have that black screen. Also swapped the dashboard location to E:\Dashboard, and restored the original soft mod dash, and still the black screen shows for about 10 secs.
  12. Hello, recently soft modded (rocky5) my Xbox, with no problems, upgraded the HDD to 250GB, and swapped the dash location to C:\Dashboard changing the dash to Evox. The issue is - upon boot the flubber animation plays, the Microsoft logo appears at the bottom, and then a black screen for about 10 or so seconds. Was wondering is this a common thing, or if not is there a possible fix ?, maybe such as showing the Xbox logo screen until the dash loads. Any help or ideas would be appreciated. Thanks.

Board Life Status


Board startup date: April 23, 2017 12:45:48
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.