Search the Community
Showing results for tags 'slim xbox'.
Found 1 result
Updated 4/25/17 Slim Xbox Original Laptop Build Photos are attached below. Hey everyone this is a log for my very own Ultra 5cm Slim Xbox Original Laptop Build. The goal for this build is to keep the Xbox originals originality by using the Xbox original case and to slim it down into an Xbox original laptop with wicked accessories. The Xbox will be cut down to just above the controller ports. The sides of the lid and the back corners of the lid will be cut off, sanded and reattached to the bottom of the case. The Xbox will then have a removable top plastic flat cover and or palm rest added to the case to replace the original lid. The original lid will no longer have sides or back corners on it, the lid will be cut to fit a Laptop LCD screen which will be powered on through the Xbox's Molex cable by using a shortened Y splitter cable. This cable will turn the Xbox's hard drive on and the Xbox's LCD screen on. The Molex cable Y splitter, splits the Amps the new Xbox pico psu outputs while the voltage remains the same. The LCD screen will either be a 15.6 inch laptop screen or a slightly smaller screen around 14 inches and will have a frame on the front of it and a cover on the back of the lcd. Two Xbox jewels will be used at the moment on this Laptop build. One jewel will be used and attached either in the center and or bottom right of the Xbox's LCD screen back cover. Another jewel will be cut into a rectangle around the Xbox logo and will be flipped over to the Xbox indentation logo side and displayed on the front of the console. There will be two to three models of the Xbox Ultra Slim Laptop at the moment, one will include two wireless controller inbuilt and will be the first model, and will be build into the Xbox Original case. The second model and third model details are yet to be released. Accessories included The accessories which are included are: The Xbox disc drive, modified into an external sata drive which can be plugged into an Xbox when its off and used easily for ripping games and playing disc games. The Xbox has to be turned off while plugging the drive into the new sata ports on the side of the Xbox and turned off while unplugging the drive. An Xbox original wireless handheld portable home device with a controller inbuilt into it. This is similar to a wii u like controller. The idea is to be able to walk around the house and be able to play Xbox as you go. These will be available for sale and the transmitter and receivers have already been tested and do transmit the video signal to screens away from the Xbox. The Xbox original will be powered by a 12volt DC 250watt pico psu, the psu is capable of outputting 20 - 20.83 amps. Whats inside the Xbox The Motherboard. The controller ports, LED modified. The 12 volt DC 250w Pico psu. A heat sink with an 80mm fan to cover the CPU A laptop IDE to sata adapter connected to the hard drive, the laptop hard drive will be positioned over the av and lan ports at the back of the console, between the ide slot and the gpu heatsink. A modified 80 wire ide cable will be used to keep the build tidy. Two Xcm wireless controller transmitters, which can be turned on and off by the use of switches on each transmitter. There will be four controllers used for this and only two can work at one time. Two controllers will be made into Wireless Xbox Portable Devices. Xbox will still be fully capable of handling wired and other plug in wireless controllers by turning off the transmitters inside the Ultra slim Xbox by the use of switches on the right hand side of the Xbox's. The Xbox will have the capacitors replaced to increase the amount of size available inside of the Xbox, by installing aluminium electrolytic capacitors which are smaller. The Xbox will contain one battery. A LCD driver board to connect the LCD to the Xbox's video signal. Two speakers connected to the driver board, receiving the audio signal from the Xbox's motherboard. An 80 wire ide cable. A Molex Y Splitter cable. A wireless xbox original internet receiver. An Ide to sata adapter on the left hand side of the Xbox positioned next to the ide port for the Xboxs external disc drive and other external accessories. LED Strips A custom assembled ATX cable. A 5volt sb to 3.3 volt standby converter made by me A 5volt sb to 3.3 volt standby converter final made by and purchased from N64 Freak. A 1tb - 2tb laptop drive. In total 2x 1tb - 2tb laptop hard drives drives, In the bigger laptop model, through the use of a hard drive selector and possibly modified original disc drive. Switches to allow for the turning on and off of the wireless Xbox controller transmitters and for the swi An additional fan port GPU heatsink Additional fans Power button Eject button Plastic to isolate the laptop hard drive and ide to sata adapter from the motherboard. Four Xbox Screws for the controller ports Six Screws to replace the Xbox original case mount screws. To hold the top casing with the bottom casing. HDMI Composite converter board, purchased from N64 Freak. Slide in DVD drive, possibly in this model or another model, although will only play burnt games and dvds and not Xbox Original games at this stage. Eight 1500uf 6.3 volt capacitors to replace the original 1500uf capacitors and the 3300uf 6.3 volt capacitors. At this stage possibly a new soldered on board ATX right angle plug for the Xbox original. At this stage possibly a new soldered on board ATX right angle plug for the Pico Power Supply. Xbox hard drive isolation and Xbox hard drive ide to sata adapter isolation. Xbox power supply isolation. Xbox heatsink isolation support. 15.6 inch or 14inch laptop screen with matching driver board. Additional 64mbs of ram, to make the Xbox have a complete 128mbs of ram. Xbox duo x chip or aladdin chip. Multiple USB ports, to allow for mouse and for inbuilt directly wired keyboard functionality for use on the Xbox Originals XBMC dashboard and on the Xbox original avaliable operating systems, including at the moment Linu , Windows 98, and Windows CE. The Xbox External Disc Drive Power button will be cut off from the eject board/power on board and wired directly back to the eject board while the eject board is mounted else where in the case. The IDE port will have an IDE to sata connector directly wired to it for the external disc drives port to best fit in the Xbox Ultra Slim Laptop, while a single double ide cable will be used to go from the ide port directly to the laptop hard drive. The disc drive will be made an external accessory by using its own IDE female to sata adapter plugged which will be plugged into the back of disc drive and use a sata cable to connect to the sata ports on the side of the Xbox Ultra Slim Laptop. An Xbox dvd drive power cable extension and port will be added as follows, Male to Female connector, which then goes from the Female connector to the Xbox left hand side mounted Male connector. The male connector which will be added to the side will allow for the power, eject in, eject out, to be connected to the drive. To avoid the Xbox throwing an Error from the drive not being connected in general, the Xbox will be chipped or tsop flashed. If the sata doesn't work due to the Xbox originals DVD drive adapter not having a slave pinner, an ide cable will be used instead. The Wireless Controller Device The Wireless controller device will include a video transmitter connected into the Xbox originals av port which will be powered by the Xbox's power new pico power supply or battery power included within the Ultra Slim Xbox Original Laptop Build. The transmitter is capable of transmitting the Xbox's video signal to another LCD screen when the video receiver is plugged into the composite av video port if that LCD screen. The video receiver will be powered by battery and will be connected to an LCD screen. The LCD screen will have a wireless controller build around the screen, inside of a custom case, which will likely be build out of an Xbox original case, to keep the Xbox's original case style. The back of the device will have an Xbox Original Jewel mounted. The wireless controllers being used are XXX XCM Wireless controllers these controllers are power by battery. The power required to use the controllers, an LCD screen, blue tooth speakers and the video receiver will be combined within the handheld device and the batteries will be rechargeable. The Project Log 1 Here's the ultra slim laptop at the moment. I have cut the power and eject button in half and will jump the power to the eject board. The eject button will be mounted on the front of the Xbox. The power button will stay in its originally place. The eject half circle hole where the eject button used to go will be fitted with leds for an on light and standby light. The original led lights for the Xbox errors will be present still. The power supply is a 12volt, 250 watt power supply, that will be turned on by battery. The power supply is almost set up at this time, although the wiring is not yet finished at this time. The Xbox is working at this stage with the new installed capacitors.
Board Life Status
Board startup date: April 23, 2017 12:45:48