Jump to content
OGXbox.com

Search the Community

Showing results for tags 'pad'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Rules
    • Why Can't I Download?
  • Subscribed Members Only
    • Subscribed Members Only
  • Off Topic
    • New Member Introductions
    • Rumble Pit
    • Suggestion Box.
  • General Xbox Discussion
    • General Xbox Discussion
  • Original Xbox Modding Forum
    • Hardware Mods
    • Modchips
    • TSOP Flashing
    • Softmods
    • Repair
  • Xbox Case Modding
    • Case Mods
    • Lighting & Electrical Mods
  • Tutorials
    • Official Tutorials
    • Tutorial Submission
  • Software
    • Bios
    • Dashboards
    • Installation Disks
    • Applications
    • Games
    • Emulators
    • Homebrew
  • Xbox Collecting
    • Xbox Collection Showcase
  • Rare and Uncommon
    • Rare and Uncommon Xbox Hardware
    • Rare and Uncommon Xbox Software
  • Vendors
    • N64 Freak's Products
    • Barnito's Products
  • Development
    • Rocky5's Projects
  • Online Play
    • Game Night
  • Classifieds
    • Wanted
    • For Sale
  • Moderator Section
    • Moderator Back Room

Product Groups

  • Vendor Forum
  • Membership Subscriptions
  • Forum Ads

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


About Me

Found 6 results

  1. Hello everyone, I'd like some help repairing my Xbox. I got an Alladin chip but while soldering I ripped the ground pad, now my Xbox won't boot to a dashboard with or without the chip. The behavior is at follows: Boots up flickering 3 times and reboots 2 times, the third time it boots either to XBlast or flickers red and green if booting to a flashed BIOS or without the chip. I've checked the dashboards, and the C drive has a lot of them for most BIOS options and so is the E drive so there should be no issue. I don't have the best tools for precise jobs, and this is my first soldering work. I have flux and it's old, dark colored and leaves quite a bit of residue as seen on the 4th picture, unsure if that's an issue though. What can I do here? Do I cut the hanging trace and connect to ground elsewhere or solder both trace ends to the pad again, etc And would the copper wire, as seen in the last picture, be enough for connecting the D0 to ground? I don't have 30ga or any type of wire as shown in videos and guides. Thanks
  2. From what I can tell I butchered my r7d3 pad on the top of the 1.0 board. The bottom pad I did fine but I'm looking for the alternative now. I was looking at the pictures but just can't tell where to place the jumper now. Any help would be greatly appreciated. I linked a picture where I think I can and a picture of the board .Thanks !! From what I can tell I butchet d my r7d3 pad on the top of the 1.0 board. The bottom pad I did fine but I'm looking for the alternative now. I was looking at the pictures but just can't tell where to place the jumper now. Any help would be greatly appreciated. Thanks !! http://imgur.com/gallery/EDufPoH http://imgur.com/gallery/ZkWBmNA
  3. Hi, i have a xbox 1.6 and I am replacing the Transistor but I accidentally took of 2 of the point for the Transistor. I really need help
  4. Does anyone have any original xbox controller that is pad hacked. I want to build arcade cabinet.
  5. I lifted the pad on R7D1, attempting to enable TSOP. is there an alternative point?
  6. If anyone out there has a link or tutorial on how to pad hack an OGxbox controller to arcade setup, id much appreciate it. Thanks

Board Life Status


Board startup date: April 23, 2017 12:45:48
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.