archfranck

go sleep dave se you tomorrow ciao

I have the same, but I only have the raw image of 2 tb and 500 gb, I miss from 1 tb, so I must first put all the games and then make me a raw image and save it for the next time. ahh ma il tuo è 3.0 and withot pc ahhhh good I did not know it could be done without a pc but I believe that with mine it cannot. my is IDE and SATA and no possible SATA- SATA send my link buy..amazon ebay

Dave 2:30 hours open xbox is ok.. i have copied 60 gb.. no close.. Dave I thought you were English, instead you are Australian, on the other side of the world. In fact, I didn't understand why you had that car that I don't know here in Europe ... eheh Ok finish copy last game and sleeep

Disclaimer: I take no responsibility if you damage your motherboard, X-Box or person when doing this tutorial. Do so at your own risk. It has been pointed out by chunkhead from the afterdawn.com and llama.com Forums that some X-Box motherboards have a corrosion problem on some traces. This corrosion is due to some sort of contamination from the factory. Due to this corrosion, it was found that some X-Boxes affected can produce the following symptoms: (1) The X-Box fails to power down using the power on/off button on the front panel. The power cord has to be pulled out to shut it down. (2) As soon as the power cord is plugged in, the X-Box powers up without pressing either the on/off or eject buttons. (3) While the X-Box is on for a certain amount of time, it shuts down by itself for no reason. The time factor before shut down can vary wildly. These symptoms are identical to mine so I believe that those soldering of A-B-C wires may have solved it

yes but for now I am copying files to a 1 TB 1 hour and a half hardisk and it has not turned off, if you were to turn off check that circuit

for now everything is working I'm copying files to a 1 TB hardisk

dave I don't know how but it works all power button ok and I kept it on 1 hour and everything ok ... I close everything screws and everything, I put hard disk 1 tera and I don't open it anymore .. heheheh ... moment of luck

Dave last update, I also welded the point C with the pasta and I also did it badly because I put too much and I was afraid it would touch the point B. Anyway, I got tired and reassembled everything. I tried to turn it off and on 3 times and it works properly it turns off and on again properly now I try to keep it a little on let's see if it goes off. But this I think is another problem the fact that after 10-20-30 min it turns itself off. But I no longer want to waste time with this xbox.

track green no continuity track red continuity

xbox open or off ? Power on or off? my xbox is 1.4 but i see in other image , v.1.4 point is same.. connect purple whit blu and measure continuity?

azz same problem now 30 min and power offf...booooo if have time connect point C-D-E and stop and other xbox

Australia ahhhhhh i think england hahahaah .. ok then the power button worked only the first time now it does not go anymore, and as soon as I turn off the dash it restarts by itself. The positive side for now is that it doesn't turn off, I kept it on for more than 1 hour and it didn't turn off. Maybe for the power button I also have to connect the points C-D-E. Maybe I see how it works in case I connect them even if they gave me continuity, maybe they are breaking.

then Dave realized that only tracks A and B were interrupted although I also soldered C. I used the soldering iron on the one hand easier and the other with the paste .. which, however, hardens as soon as it hardens. I reassembled everything and in the meantime the power function button .. for now I have turned on the xbox for 10 minutes and it still hasn't turned off ... maybe I did it ... damn you are fantastic in this forum ... in Italy there are no such experts .. I believe that the British are the best in dealing with the Xbox 1 model

ok i try and i will let you know the results eheheh

Dave I had an idea I could use conductive paste, for the tsop it worked, then I noticed that it becomes hard enough so I could place it over the wire and with an adhesive tape hold it 1 hour and it becomes hard it is easier with the syringe I don't risk burning anything with the soldering iron. Anhe if I put too much and goes on the next track I do not risk because the motherboard and the tracks next to it are isolated .. according to me it is a method to try .. now I do tests on a test circuit and see after how hard it hardens.

the last xbox where I made the tsop with conductive paste is a version 1.4, but in the tutorial I speak of 1.0-1.1 or 1.2-1.3 but not of 1.4 ... it is the same as for the v. 1.2-1.4?

yes i have..colour yellow but equal... ok come on I dedicate myself to those tracks of the button on off then calmly step to 2 xbox 1.6

ok azz eheheh i think my problem is track a-b-c ok if have time try ... next week i have 2 xbox 1.6 ...softmod or chipmod?? I already know your answer

hard disk 1 tb is ok i put in other xbox.. cable is ok and sata adaptador is ok.. I think you're right it seems to me that some tracks are interrupted, but repairing it is impossible for me too small ... and however this could be the problem with the power button. But I have another problem which after 3-4-5-10 min turns itself off.

always problems ... check tonight ... ok dave thanks

no I am not understanding anything anymore .. now it does the same ignition problem and I was unable to install the dash after 20-sec sometimes after 2-3 min it turns off everything .. I have to understand if it is a cable adapter problem ide or hardisk

now everything works I put the 80 wires cable and adapter and hardisk and it works both the shutdown and it has also detected the new hardisk ... everything is going well now I format and install dash let's see for the partitions if I have problems

It has only one problem I noticed .. that if I open it from the dashboard it turns back on by itself and I have to turn it off from the power button. But then the power does not turn on but from the eject button .. the trolley comes on and then I have to close it again ... I don't know .. but it does nothing

i think this hard disk no compatibily.. now try

ok fixed boot dash now xbmc. So now I have the tsop and can I put any hardisk without cloning as for the soft mod? I have this 1 terabite hard disk with 80 pin cable and sata adapter. But it gives me recognition problems now I try again. Anyway with the conductive paste and the small syringe it's really easy.