neighbor Posted March 13, 2019 Report Share Posted March 13, 2019 Ryzee, you moved to asia? 1 Quote Link to comment Share on other sites More sharing options...
Ryzee119 Posted March 16, 2019 Author Report Share Posted March 16, 2019 (edited) Got a few up on etsy now https://www.etsy.com/au/Ryzee119/listing/672315615/ogx360-add-wireless-xbox-360-controller Edited March 16, 2019 by Ryzee119 5 Quote Link to comment Share on other sites More sharing options...
TEK Nemesis Posted March 16, 2019 Report Share Posted March 16, 2019 Is there potential that you could simply remove the components from inside the MS receiver and install them into an enclosed plastic case with your board? Quote Link to comment Share on other sites More sharing options...
Ryzee119 Posted March 16, 2019 Author Report Share Posted March 16, 2019 29 minutes ago, TEK Nemesis said: Is there potential that you could simply remove the components from inside the MS receiver and install them into an enclosed plastic case with your board? Sure why not. Still need to plug the receiver into the USB port or solder the wires from the receiver to behind the usb port for a smaller finish. Add a hole to access the sync button and it should work fine. 2 Quote Link to comment Share on other sites More sharing options...
bluemeanie23 Posted March 17, 2019 Report Share Posted March 17, 2019 https://mega.nz/#!79lkRCDZ!WcDRWjnYFfR8U2j5I8tN8G3IIa-aKAbxvVsmtPItriw 3d printed case and lid for ryzee119's OGX360 print details layer height 1-2mm infil 20%-100% any where in between still prints fine but 100% is more sturdy 4-6 solid bottem layers 4-6 perimeter shells 4-6 solid top layers 215c extruder temp 65c bed temp #the Case does need to print with supports# A big shout out to ryzee119 for all his hard work 4 Quote Link to comment Share on other sites More sharing options...
big F Posted March 17, 2019 Report Share Posted March 17, 2019 Nicely done. Once I get my workshop straight Im planning to start the internal solution, with 3D printed bits where needed. The boards came back from the fabricators bundled up with my boards for my Amiga project days ago..... Still waiting on some components for the build. The pain is, some for the board are here but nothing I can install with out causing problems later, same goes for the Amiga boards. 2 Quote Link to comment Share on other sites More sharing options...
bluemeanie23 Posted March 17, 2019 Report Share Posted March 17, 2019 6 minutes ago, big F said: Nicely done. Once I get my workshop straight Im planning to start the internal solution, with 3D printed bits where needed. The boards came back from the fabricators bundled up with my boards for my Amiga project days ago..... Still waiting on some components for the build. The pain is, some for the board are here but nothing I can install with out causing problems later, same goes for the Amiga that sounds like a bloody good idea mate. ahhh the snail mail waiting game I've played this one a few times it's quite painful Quote Link to comment Share on other sites More sharing options...
big F Posted March 17, 2019 Report Share Posted March 17, 2019 (edited) Well here are my boards patiently waiting the delivery of the components. May well start the mock up process without them though since I can calculate the size with everything soldered on. Plus no worries for static on an empty board. They are white as the rest of my order is also white. It should look great in my clear Xbox Edited March 17, 2019 by big F 4 Quote Link to comment Share on other sites More sharing options...
Xbmcmodsforxbox Posted March 17, 2019 Report Share Posted March 17, 2019 I love that white color look on those boards Quote Link to comment Share on other sites More sharing options...
Ryzee119 Posted March 18, 2019 Author Report Share Posted March 18, 2019 @bluemeanie23 Mate, that case is awesome and thank you for creating something! Would you be happy for me to add to my github page? 2 Quote Link to comment Share on other sites More sharing options...
Ryzee119 Posted March 18, 2019 Author Report Share Posted March 18, 2019 (edited) @big F That white , just need matching Arduino modules somehow Edited March 18, 2019 by Ryzee119 Quote Link to comment Share on other sites More sharing options...
Ryzee119 Posted March 18, 2019 Author Report Share Posted March 18, 2019 (edited) This is a simple case that I put together which I just got laser cut. 3mm acrylic sheets laser cut using cap head screws and hex standoffs. Ogx360 is supported with thick double sided foam adhesive tape. I probably won't sell them as the logistics are too hard for me at the moment, but I will upload the DWG files to my github soon for laser cutting from your local hackerspace or online ogx360caseRyzee119.pdf Edited March 18, 2019 by Ryzee119 2 Quote Link to comment Share on other sites More sharing options...
big F Posted March 18, 2019 Report Share Posted March 18, 2019 41 minutes ago, Ryzee119 said: @big F That white , just need matching Arduino modules somehow Yeah that would be awesome. I’m unsure why this has never been an option already. For the price that you can buy them at the likes of AliExpress. They mint them out on panels dozens at a time. It wouldn’t cost anymore. The couple of companies I use for board fabbing don’t really care what colour you want the board finished in, they are more interested in Gold finishing or assembling it for you. There is IMO a whole market there for coloured boards, it’s only laminate lacquer after all. I can go to the local DIY store with a piece of cloth, soil or what ever and they can match it and make me some paint, so why not with pcbs etc. 1 Quote Link to comment Share on other sites More sharing options...
Ryzee119 Posted March 18, 2019 Author Report Share Posted March 18, 2019 (edited) 7 minutes ago, big F said: Yeah that would be awesome. I’m unsure why this has never been an option already. For the price that you can buy them at the likes of AliExpress. They mint them out on panels dozens at a time. It wouldn’t cost anymore. Im sure there is a seller on Ali who would do a run of a custom colour for you. Although the MOQ might be a bit My quote for a custom Xbox to MicroUSB cable for this project was MOQ of 1000 units ($840 USD FYI) never proceeded with the quote. Edited March 18, 2019 by Ryzee119 Quote Link to comment Share on other sites More sharing options...
bluemeanie23 Posted March 18, 2019 Report Share Posted March 18, 2019 1 hour ago, Ryzee119 said: @bluemeanie23 Mate, that case is awesome and thank you for creating something! Would you be happy for me to add to my github page? no worries mate throw it up 2 Quote Link to comment Share on other sites More sharing options...
irlandez Posted March 18, 2019 Report Share Posted March 18, 2019 (edited) 17.03.2019 в 05:06 Ryzee119 сказал: Получил немного etsy сейчас https://www.etsy.com/au/Ryzee119/listing/672315615/ogx360-add-wireless-xbox-360-controller Hello, are you sending your gadget to Russia? Edited March 18, 2019 by irlandez Quote Link to comment Share on other sites More sharing options...
Anarchy42085 Posted March 23, 2019 Report Share Posted March 23, 2019 On 3/16/2019 at 9:07 PM, bluemeanie23 said: 3d printed case and lid for ryzee119's OGX360 Thanks for the design @bluemeanie23 2 Quote Link to comment Share on other sites More sharing options...
bluemeanie23 Posted March 23, 2019 Report Share Posted March 23, 2019 5 hours ago, Tony Kuberka said: Thanks for the design @bluemeanie23 here's the link for the 3d model in Tinkercad u can personalize it yourself quite easily thru your browser enjoy https://www.tinkercad.com/things/kJb02GCUetG 2 Quote Link to comment Share on other sites More sharing options...
Ryzee119 Posted April 1, 2019 Author Report Share Posted April 1, 2019 Working on 8bitdo usb adaptor support! It was very picky and needed a sequence of usb packets on initialisation to keep it active. Still testing but should support everything the 8bitdo website says. (Bluetooth xbone, ps3, ps4 all 8bitdo controllers etc.) 5 Quote Link to comment Share on other sites More sharing options...
Anarchy42085 Posted April 1, 2019 Report Share Posted April 1, 2019 (edited) 1 hour ago, Ryzee119 said: Working on 8bitdo usb adaptor support! Will it support 4 controllers connected to it at one time? Put me down for one when you get it going!! I would love to use my 8bitdo controllers on my xbox!! Edited April 1, 2019 by Tony Kuberka 1 Quote Link to comment Share on other sites More sharing options...
Ryzee119 Posted April 1, 2019 Author Report Share Posted April 1, 2019 Seems like the 8bitdo adaptor only supports one controller at a time. If I go to sync another it just drops the first one.. Looks like this will be one player only. (Unless you use a USB hub and multiple 8bitdo adapters, which should work in theory but untested) I will post an update here when ive finished testing and added it to github. Just a firmware update required to existing units. Quote Link to comment Share on other sites More sharing options...
XC-3730C Posted April 1, 2019 Report Share Posted April 1, 2019 I would have pro with 8bitdo controllers working hower they can on an OG Xbox.Sent from my SM-G955U using Tapatalk Quote Link to comment Share on other sites More sharing options...
Acidmank Posted April 3, 2019 Report Share Posted April 3, 2019 Have i missed th boat on this one? Will there be any more coming up for sale? 1 Quote Link to comment Share on other sites More sharing options...
Ryzee119 Posted April 4, 2019 Author Report Share Posted April 4, 2019 There will be more. Just been very busy IRL so havnt had a chance to organise another order 1 Quote Link to comment Share on other sites More sharing options...
Xbox4rl Posted April 4, 2019 Report Share Posted April 4, 2019 I want one pls!! With support for 4 controllers. 2 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.