Phantom Hobo Posted February 18, 2019 Report Share Posted February 18, 2019 I would'nt mind the receiver outside of the xbox, but the chip i would prefer inside. hmm need to see about how to solder this inside. Quote Link to comment Share on other sites More sharing options...
elierodrigue Posted February 19, 2019 Report Share Posted February 19, 2019 Looking foward to it! Quote Link to comment Share on other sites More sharing options...
Jonathon Trahan Posted February 19, 2019 Report Share Posted February 19, 2019 now if only we could get it to turn on and off the console for us lol 2 Quote Link to comment Share on other sites More sharing options...
neighbor Posted February 19, 2019 Report Share Posted February 19, 2019 (edited) 50 minutes ago, Jonathon Trahan said: now if only we could get it to turn on and off the console for us lol it should receive current from another source other than USB ports, also should be enough to figure how to bridge ON/OFF contacts (when needed) from the front panel, I guess. But this thing is way more complex, as it's not a native controller. Looking forward to Ryzee's answer to this. Edited February 19, 2019 by neighbor Quote Link to comment Share on other sites More sharing options...
Ryzee119 Posted February 20, 2019 Author Report Share Posted February 20, 2019 Well it would be quite simple to use the spare GPIO and have them activate on some button combo. If the gpio pin is wired accordingly these could be used to turn on/off LEDs, eject the dvd tray and maybe turn OFF the console. But to turn ON, neighbor is right, it would need some 5V supply from somewhere which is available when th4 xbox is in standby. The board draws about 100mA, so the standby current would increase by the same amount. Bit more tricky so would need to give that extra thought. 1 Quote Link to comment Share on other sites More sharing options...
bluemeanie23 Posted February 22, 2019 Report Share Posted February 22, 2019 On 07/02/2019 at 7:56 AM, evertonstz said: You'll be selling those? Lost Ryzee's selling Also are you willing to sell them without the atmega? I have dozens of them around here, lol. if you want to purchase a already setup board or some bare pcbs please refer to ryzees etsy or shoot him a msg mate😊 1 Quote Link to comment Share on other sites More sharing options...
KaosEngineer Posted February 22, 2019 Report Share Posted February 22, 2019 (edited) The Xbox's always-on standby power supply is 3.3Vdc on all versions except the 1.6's where it is 5Vdc. Edited February 22, 2019 by KaosEngineer 1 Quote Link to comment Share on other sites More sharing options...
Jonathon Trahan Posted February 24, 2019 Report Share Posted February 24, 2019 On 2/19/2019 at 8:08 PM, Ryzee119 said: Well it would be quite simple to use the spare GPIO and have them activate on some button combo. If the gpio pin is wired accordingly these could be used to turn on/off LEDs, eject the dvd tray and maybe turn OFF the console. But to turn ON, neighbor is right, it would need some 5V supply from somewhere which is available when th4 xbox is in standby. The board draws about 100mA, so the standby current would increase by the same amount. Bit more tricky so would need to give that extra thought. 6 Possibly a small boost converter from the 3.3v line? Also, how possible would it be to repurpose this to work with xbox one controllers? Quote Link to comment Share on other sites More sharing options...
Ryzee119 Posted February 25, 2019 Author Report Share Posted February 25, 2019 23 minutes ago, Jonathon Trahan said: Also, how possible would it be to repurpose this to work with xbox one controllers? I already have firmware which supports wired Xbox one on my github. The wireless Xbox one receiver is very complex so I have not been able to write my own driver for it Adding a Bluetooth dongle may be the best way but I haven't got it working yet. So the answer is it is possible. 1 Quote Link to comment Share on other sites More sharing options...
XC-3730C Posted February 25, 2019 Report Share Posted February 25, 2019 When will these be for sale again?Sent from my SM-G955U using Tapatalk Quote Link to comment Share on other sites More sharing options...
Ryzee119 Posted February 27, 2019 Author Report Share Posted February 27, 2019 On 2/25/2019 at 2:13 PM, XC-3730C said: When will these be for sale again? Should have 50 units in about two-three weeks 1 Quote Link to comment Share on other sites More sharing options...
Sutt359 Posted February 27, 2019 Report Share Posted February 27, 2019 I cant wait to order many for my system mods, how much are they any how? Cheers Quote Link to comment Share on other sites More sharing options...
Daver80 Posted February 27, 2019 Report Share Posted February 27, 2019 Hi again, just wanted to post a link to a video I just uploaded to YouTube, I have a little gaming channel there and thought this mod was so cool and unique I just needed to mention it in a video. Hope you enjoy:) 2 Quote Link to comment Share on other sites More sharing options...
Noobstarr Posted March 4, 2019 Report Share Posted March 4, 2019 The XERC modchip allows for powering on the xbox through the 360 controller Quote Link to comment Share on other sites More sharing options...
Ryzee119 Posted March 5, 2019 Author Report Share Posted March 5, 2019 7 hours ago, Noobstarr said: The XERC modchip allows for powering on the xbox through the 360 controller Ill have too look into that, but I thought it let you use an IR remote with a IR receiver to trigger on/off etc? Quote Link to comment Share on other sites More sharing options...
neighbor Posted March 5, 2019 Report Share Posted March 5, 2019 5 hours ago, Ryzee119 said: Ill have too look into that, but I thought it let you use an IR remote with a IR receiver to trigger on/off etc? that's true, the guy probably forgot to put a question mark. Quote Link to comment Share on other sites More sharing options...
Noobstarr Posted March 5, 2019 Report Share Posted March 5, 2019 7 hours ago, Ryzee119 said: Ill have too look into that, but I thought it let you use an IR remote with a IR receiver to trigger on/off The 360 controller middle button is IR Quote Link to comment Share on other sites More sharing options...
Noobstarr Posted March 5, 2019 Report Share Posted March 5, 2019 here is the XERC 2 XE user manual, check out the bottom Quote Link to comment Share on other sites More sharing options...
KaosEngineer Posted March 5, 2019 Report Share Posted March 5, 2019 (edited) There are 360 remotes that are IR (Media Center controls/DVD player), I didn't think the 360 controller had IR. It was only wireless (RF). Edited March 5, 2019 by KaosEngineer 1 Quote Link to comment Share on other sites More sharing options...
big F Posted March 8, 2019 Report Share Posted March 8, 2019 I am currently waiting on delivery of my boards got most of the components ready. I only got enough fabbed so my boxes and a friends can have this mod. my plan is to see if i can make a solution to add it internally, hoping to be able to provide a 3d printable bracket type thing. Hopefully i wont need to use dollops of hot glue instead. 1 Quote Link to comment Share on other sites More sharing options...
Ryzee119 Posted March 8, 2019 Author Report Share Posted March 8, 2019 13 hours ago, big F said: I am currently waiting on delivery of my boards got most of the components ready. I only got enough fabbed so my boxes and a friends can have this mod. my plan is to see if i can make a solution to add it internally, hoping to be able to provide a 3d printable bracket type thing. Hopefully i wont need to use dollops of hot glue instead. Look forward to seeing what you come up with with! Quote Link to comment Share on other sites More sharing options...
bluemeanie23 Posted March 9, 2019 Report Share Posted March 9, 2019 https://mega.nz/#F!S5kSESpA!gfsYmHBNwBoRtgdwxu4WeQ xerc2 gerbers 4 1 Quote Link to comment Share on other sites More sharing options...
neighbor Posted March 9, 2019 Report Share Posted March 9, 2019 (edited) 2 hours ago, bluemeanie23 said: https://mega.nz/#F!S5kSESpA!gfsYmHBNwBoRtgdwxu4WeQ xerc2 gerbers nice. btw, had an idea some time ago, to create a small circuit with IR led, button and a chip which will just reproduce the same command which XERC 2 will recognize as ON/OFF, and install that small thing into the Xbox controller. It will take me some time to make it real, because I have no skill at this, maybe you would be interested to create such thing? Edited March 9, 2019 by neighbor 1 Quote Link to comment Share on other sites More sharing options...
Ryzee119 Posted March 9, 2019 Author Report Share Posted March 9, 2019 6 hours ago, bluemeanie23 said: https://mega.nz/#F!S5kSESpA!gfsYmHBNwBoRtgdwxu4WeQ xerc2 gerbers Sweet man, thanks for sharing. 4 hours ago, neighbor said: nice. btw, had an idea some time ago, to create a small circuit with IR led, button and a chip which will just reproduce the same command which XERC 2 will recognize as ON/OFF, and install that small thing into the Xbox controller. It will take me some time to make it real, because I have no skill at this, maybe you would be interested to create such thing? Yep if you could integrate an IR transmitter with the right signals into an x360 wireless controller (or any controller I guess) + xerc2 in the console it could work. 1 Quote Link to comment Share on other sites More sharing options...
Ryzee119 Posted March 13, 2019 Author Report Share Posted March 13, 2019 Not even half 4 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.