emiliano Posted January 11, 2022 Report Share Posted January 11, 2022 good evening Request If I take the component signals before the 0.27ohm resistors to install an internal wii2hdmi, do you think it can be a problem? Would it still work? Anyway tomorrow I'll try Quote Link to comment Share on other sites More sharing options...
SS_Dave Posted January 12, 2022 Report Share Posted January 12, 2022 3 hours ago, emiliano said: good evening Request If I take the component signals before the 0.27ohm resistors to install an internal wii2hdmi, do you think it can be a problem? Would it still work? Anyway tomorrow I'll try They are not resistors they are inductors and yes you could take the signal before the inductor but Why?? Cheers SS Dave Soft modding is like masturbating, It gets the job done but it's nothing like the real thing. Quote Link to comment Share on other sites More sharing options...
emiliano Posted January 12, 2022 Author Report Share Posted January 12, 2022 I wanted to get it earlier to make it easier to solder the plate. anyway I tried. taking the signal first the screen remains black Quote Link to comment Share on other sites More sharing options...
SS_Dave Posted January 12, 2022 Report Share Posted January 12, 2022 I use a PCB like this. You solder the wii2hdmi to the larger board 1st and solder the correct small board (Lower) to the Xbox then solder the two together. Cheers SS Dave Soft modding is like masturbating, It gets the job done but it's nothing like the real thing. 1 Quote Link to comment Share on other sites More sharing options...
emiliano Posted January 12, 2022 Author Report Share Posted January 12, 2022 yes I know how. i use pcbs found on dirtypcbs better than crazy asylum ones more refined. indeed if you have the gerber of dirtypcbs you would be doing me a great favor Quote Link to comment Share on other sites More sharing options...
emiliano Posted January 14, 2022 Author Report Share Posted January 14, 2022 today i got this wii2hdmi new models. I had to redesign the 3d plate. what do you think? it is a little longer so it is easier to weld at the back. the only shrewdness is to raise the quartz otherwise it touches Quote Link to comment Share on other sites More sharing options...
emiliano Posted January 14, 2022 Author Report Share Posted January 14, 2022 Quote Link to comment Share on other sites More sharing options...
emiliano Posted January 14, 2022 Author Report Share Posted January 14, 2022 (edited) Edited January 14, 2022 by emiliano Quote Link to comment Share on other sites More sharing options...
SS_Dave Posted January 15, 2022 Report Share Posted January 15, 2022 5 hours ago, emiliano said: Must be a different wii2hmi 5 hours ago, emiliano said: I just use flush cutters and trim the leads down to the board when needed Cheers SS Dave Soft modding is like masturbating, It gets the job done but it's nothing like the real thing. Quote Link to comment Share on other sites More sharing options...
emiliano Posted January 15, 2022 Author Report Share Posted January 15, 2022 better raise it with the wire cutters remain spikes that I can cut a track that passes right under them Quote Link to comment Share on other sites More sharing options...
emiliano Posted January 16, 2022 Author Report Share Posted January 16, 2022 (edited) I would like to retouch the crazy asylum project as I would like to create a new hole for the position of the quartz, arrange the 3 rgb pads as they are milled too much and remove the cut on the lower gerbers of the 3 audio and 5v pads Does anyone have the initial project? Editing directly from gerbers is problematic Edited January 16, 2022 by emiliano Quote Link to comment Share on other sites More sharing options...
emiliano Posted October 22, 2022 Author Report Share Posted October 22, 2022 (edited) good morning everyone. I have several wii2hdmi that have the FS9299 chip but unfortunately the brightness is very low. I tested a wii2hdmi with 9288A chip and I have to say it's very good. Do you know where to find wii2hdmi with this chip? Thank you Edited October 22, 2022 by emiliano Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.