Jump to content

Recommended Posts

How are you networking your Xbox and PC?

FTP Client applications: FileZilla, Core FTP LE Free Edition, WinSCP.

Make sure the PC and Xbox have an IP address and they are both on the same subnet.

192.168.1.xxx and 192.168.1.yyy

not

192.168.0.xxx and 192.168.1.yyy

For most home routers the subnet mask is 255.255.255.0 which means the first three dotted decimal values have to match for the devices to be able to communicate with each other (e.g. 192.168.1).  Each device on the subnet has to have a unique address.  The 4th dotted decimal value between 1 and 254 not assigned to any other device on the network.  

Userid and password for the Xbox's FTP server have a default setting of xbox and xbox.

 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Content

    • By dragon30561
      Dvd drive power cord got shorted out now the xbox turns on and off twice then stays on with no video.
      No visible damage to mother board could I have wiped the tsop by shorting out the cable?
      Tryed swapping power supply from working xbox samething 
    • By nabilrezki
      Hi, i bought an xbox for 10€ a couple of months ago, i had to clean it, removed the clock capacitor and i also did a tsop flash (evox m8 bios)
      I added a 500gb hard drive, wich works quite fine, i tested it on another xbox and even a xbox 360! The thing is, the xbox takes a long time to boot, like 30 seconds, my other tsop 1.4 xbox takes no more than 15secs (give or take).
      I took a cheap chinese ide to sata for the xbox, it work well on my other xbox so i don't suspect that the problem can come from this. At first i thought that it was coming from the 80pins ribbon wich wasn't long enough, so i bought a longer one, but it didn't change anything.
      And on top of that, when i press both triggers + start + back in order to go back to my main dash, the xbox take at least 10 to 15 seconds to give me an error 07
      I suspect the dvd drive to be the issue, but why will it start with no other problem that the long boot when i press the power button, but fail to reboot when i press both triggers+start+back ? By the way i can hear two spins from the dvd drive, i think the xbox check if there is any dvd on it, so i tryed to insert a xbox game and the hexen disc, it loads, it takes a long time to load, but still..
       
      So, is there any way to bypass the dvdcheck to see if it's come from this, whithou having to make any power modification ? i read that it's possible by disable dvd check on a certain bios + hardwares modifications wich i'm not feeling quite comfortable with..
      Or if you guys think that it could come from somewhere else?
    • By Oldnice
      Hi everyone,
      I recently did a 128MB mod on an Xbox 1.1, which was successful. Console booted nice, and ran for hours while gaming, even with a small NV & FSB overclock. I decided I didn't hate myself enough, and decided to go even further and replace all the K4D263238M-QC50 on the board, with the Samsung K4D263238F-QC50-variant, which is said to be tad bit more efficient. Thought this might allow for even more OC (never enough, right?), but now I've run into issues after replacing all the memory chips on the board: The console boots, but only runs for 5-30 seconds, before the screen starts to glitch heavily, with the system freezing as well. If rebooted after a glitch, without a small pause, the system will not boot, and will flash a green light.
      I've tried to do the following:
      - Reflow all 8 memory chips 4 times in total. No improvement.
      - Removed the extra 64MB memory, retaining only the original 64MB, just with the new F-variant memory chips. No improvement.
      - Replace the remaining 4 memory chips with another, fresh, F-variant memory chips. No improvement.
      Each time I complete a step, the end result is exactly the same: XBlast runs for the same 5-30 seconds, before glitching and freezing. I can run the memory test for the extra 64MB (when I had it installed), which always completes successfully, if I manage to run it completely before the system starts to glitch. If I connect a HDD, I can even boot iND bios with UnleashX, and everything works and shows correctly, before the system glitches and freezes. Always the same screen glitch effect, before freezing.
      The Xbox is modded with an Aladdin XT+, with the XBlast enchanced 49LF080A-chip.
      I can solder, remove or reflow the chips with confidence, with clear and clean solder jobs. I can share pictures, if required, but I'm pretty sure at this point that the solder job is not to blame. Have I nicked some important component somewhere with my solder iron? Are the F-variant memory chips simply incompatible with the 1.1 board? Anyone got any leads?

Board Life Status


Board startup date: April 23, 2017 12:45:48
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.