Jump to content
OGXbox.com

Error Code 9 after flashing a new bios


UserFriendly
 Share

Recommended Posts

So I modded a 1.6 with a OpenXenium chip and flashed Evolution M8Plus 1.6. I upgraded the harddrive successfully and was launching into my new dashboard with no issues. I then went to flash a version of the EvoxM8plus that forces 480p and when I restart to test the flash I am greated with an error code 9. Brand new Seagate Barracuda 2tb HDD(ST2000DM008), brand new 80pin IDE cable, brand new startech ide to sata connector. 

I have removed the 480p bios and still getting the same result. I have removed the disk drive and still getting the same result. From my limited knowledge I feel that flashing the 480p bios is not my issue but that was literally the only thing that changed between my last successful boot. Trying to dig out my SATA to USB to look at the HDD on my PC but I have no other ideas of what could be happening, do I need to recheck my solder points?

Edited by UserFriendly
Link to comment
Share on other sites

What happens when install the stock HDD with the stock IDE cable?

Quote

Error Code 09

Problem: Hard drive parameters are missing or incorrect.

Cause/Solution: Very uncommon error. The hard drive might be in the wrong transfer mode (PIO/DMA), or set to slave instead of master. If it's a debug console, the size may be incorrect (minimum size is required for debug). Replace the hard drive otherwise.

 

Link to comment
Share on other sites

Test your origianl HDD with stock cabels and the 480p bios (Or is it already that setup?) . How ever, if that woks, something is wrong with your new HDD.

You could try to wipe your HDD (or low lvl format it) on your PC using EaseUS Partition Master or HDD LLF Low Level Format Tool or what ever you find to do the job. When thats done put it back in your xbox and see what happend. 

You could also try (as a first step) to just format it on your PC using FatXplorer 3.0 Beta 14. After that you could simply set up the HDD on your PC and then put it pack and see what happend.

Maybe you are lucky and it works first try. If not wait and see if someone else has another idea what you could try.

Edited by sweetdarkdestiny
Link to comment
Share on other sites

1 minute ago, sweetdarkdestiny said:

Test your origianl HDD with stock cabels and the 480p bios (Or is it already that setup?) . How ever, if that woks, something is wrong with your new HDD.

You could try to null your HDD (or low lvl format it) on your PC using EaseUS Partition Master or HDD LLF Low Level Format Tool or what ever you find to do the job. When thats done put it back in your xbox and see what happend. 

You could also try (as a first step) to just format it on your PC using FatXplorer 3.0 Beta 14. After that you could simply set up the HDD on your PC and then put it pack and see what happend.

Maybe you are lucky and it works first try. If not wait and see if someone else has another idea what you could try.

I did not try the 480p bios with the stock hdd and cables so I will try that next when I get some time. 

Since my new HDD worked at one point I would rather try to just reformat it again with the installer disk tool unless you really think I would be able to find out what went wrong by doing all of that.

Link to comment
Share on other sites

Posted (edited)
8 hours ago, sweetdarkdestiny said:

Test your origianl HDD with stock cabels and the 480p bios (Or is it already that setup?) . How ever, if that woks, something is wrong with your new HDD.

You could try to wipe your HDD (or low lvl format it) on your PC using EaseUS Partition Master or HDD LLF Low Level Format Tool or what ever you find to do the job. When thats done put it back in your xbox and see what happend. 

You could also try (as a first step) to just format it on your PC using FatXplorer 3.0 Beta 14. After that you could simply set up the HDD on your PC and then put it pack and see what happend.

Maybe you are lucky and it works first try. If not wait and see if someone else has another idea what you could try.

480p bios with stock HDD worked fine so I guess my new HDD just fuzzed up somehow. Going to reformat now hopefully won't happen again.

 

EDIT: So I tried cloning a different HDD that I had laying around from the stock HDD and that also did not work so possibly an issue with my SATA to IDE adapter? The pins are slightly bent from the amount of switching I've had to do but nothing too crazy. Quite frustrating as I was about to FTP some games over when this started happening initially.

Edited by UserFriendly
Link to comment
Share on other sites

Glad to hear that the 480p with the stock HDD and cable works. That means that the bios is working and your XBox and chip is ok. :)

Back 2  your problem. It could also be the IDE cable. If you have another 80 wire on hand try to chnage that. Or in some cases the 40 wire works with SATA adapter. You could try that just see see what happneds. And I would try it with a freesh fromated HDD. Use FatXPlorer 3.0 for that. ( https://fatxplorer.eaton-works.com/3-0-beta/ ).

And when FatXPlorercan read your HDD (which is hopefully unlocked?) your HDD should be also fine which leads us to either the IDE cable or Adapter.

Link to comment
Share on other sites

10 hours ago, sweetdarkdestiny said:

Glad to hear that the 480p with the stock HDD and cable works. That means that the bios is working and your XBox and chip is ok. :)

Back 2  your problem. It could also be the IDE cable. If you have another 80 wire on hand try to chnage that. Or in some cases the 40 wire works with SATA adapter. You could try that just see see what happneds. And I would try it with a freesh fromated HDD. Use FatXPlorer 3.0 for that. ( https://fatxplorer.eaton-works.com/3-0-beta/ ).

And when FatXPlorercan read your HDD (which is hopefully unlocked?) your HDD should be also fine which leads us to either the IDE cable or Adapter.

I have already reformatted my HDD once on my PC during this process to check that. What does this program do differently than any other Disk Formatting service? I have come to the same conclusion though that it must be the cable or more likely the adapter.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Similar Content

    • By chocomochino
      Hello to everyone i've been trying to find a solution for hours reading posts but i don't find my specific case:
      Xbox: 1.4 Winbond version
      i opened my Xbox and found out it had this aladdin version i thought it was softmodded; i wanted to TSOP to increase the HD (No locking on the drive i have) so i thought oh, i could just update the Bios then to support HD creation 
      then i tried with Hexen 2019 installing BIOS Evo m8 plus F; but it says: no write access allowed, i tried pressing the power button 2 seconds while booting up( to enable flash write)  nothing happened, same error;
      Anyone knows the best way to update the bios i just want to change the hard drive into a larger one (<1tb) but the drive i have has no locking features
      I already also softmodded this xbox ( i didn't know it had a modchip)
       

    • By goldenretrogames
      I just installed a 2TB SSD in my Xbox, as the previous HDD I had in it died. Once I got a dashboard installed (UnleashX 0.39.0528A), I started copying over my games. After 145 games, I started getting errors during FTP. When required, the FTP client would create subdirectories, but then trying to change in to the newly created sub directory would fail. All file uploads would fail as well. I've tried both FileZilla and WinSCP and both have the same problem.
      Here's the error from WinSCP:
      Dir already exists in cache! "/F/Games/<game name>/DATA": Directory not found.
      I deleted the cache volumes on the Xbox, but the error continues to happen. As it stands, I'm unable to upload anything else to the F volume. There's 708GB free on F, so disk space shouldn't be a problem.
      I also did a test using the File Manager app on the Xbox. I created a subdirectory in F:\Games and then copied a file from the E: over to the new subdirectory. The file doesn't show up in the subfolder.
      I did have the my games split between F and G before, but that was because of how the volumes were original configured and there wasn't enough space on a single volume. I should be able to fit everything on F, but this issue is stopping me from doing so.
      In case it matters, I'm using an M8Plus BIOS with LBA48 support which is patched for the XboxHD+. Both F and G are partitioned to about 972GB each.
    • By Absolucy
      I have a 1.0 Xbox I got from Goodwill online. It smells like a smoker crawled inside it and died, and I ended up accidentally tearing off the alt d0 pad , but got someone to repair it. However, it still does not boot, as it FRAGs instead. Can't figure out what is wrong - tons of pictures attached below.
      Things I've tried:
      Known-good PSU Booting WITH modchip + grounded d0 Booting without modchip or grounded D0 Swapping capacitors with good capacitors from a 1.1 Swapping the TSOP for one from a 1.1 Cleaning the board with IPA (multiple times) If any closer pictures are needed of any part, tell me.

Board Life Status


Board startup date: April 23, 2017 12:45:48
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.