SS_Dave Posted May 18, 2021 Report Share Posted May 18, 2021 I suspect the trace at pin 1 is the problem There should be continuity between all the red arrows I suspect there is a open circuit on the bottom Cheers SS Dave Soft modding is like masturbating, It gets the job done but it's nothing like the real thing. Quote Link to comment Share on other sites More sharing options...
Yanimo Posted May 18, 2021 Author Report Share Posted May 18, 2021 34 minutes ago, SS_Dave said: I suspect the trace at pin 1 is the problem There should be continuity between all the red arrows I suspect there is a open circuit on the bottom Cheers SS Dave Soft modding is like masturbating, It gets the job done but it's nothing like the real thing. soldered that point to pin 1 and no luck. Quote Link to comment Share on other sites More sharing options...
Yanimo Posted May 18, 2021 Author Report Share Posted May 18, 2021 59 minutes ago, SS_Dave said: I suspect the trace at pin 1 is the problem There should be continuity between all the red arrows I suspect there is a open circuit on the bottom Cheers SS Dave Soft modding is like masturbating, It gets the job done but it's nothing like the real thing. Another note it doesn't reboot after but just flashes orange then dies. I think we're getting closer to fixing this thing Quote Link to comment Share on other sites More sharing options...
SS_Dave Posted May 18, 2021 Report Share Posted May 18, 2021 Looks like you need to remove all the links/rats nest and then repair the damaged traces to get to the point where it boots without the modchip even if it's to a error on the screen. Also a different list of error led flash tells me it could be over heating You should have close to the voltages in this diagram Cheers SS Dave Soft modding is like masturbating, It gets the job done but it's nothing like the real thing. Quote Link to comment Share on other sites More sharing options...
Yanimo Posted May 18, 2021 Author Report Share Posted May 18, 2021 8 minutes ago, SS_Dave said: Looks like you need to remove all the links/rats nest and then repair the damaged traces to get to the point where it boots without the modchip even if it's to a error on the screen. Also a different list of error led flash tells me it could be over heating You should have close to the voltages in this diagram Cheers SS Dave Soft modding is like masturbating, It gets the job done but it's nothing like the real thing. Thank you Will do this and it may take a while. Quote Link to comment Share on other sites More sharing options...
SS_Dave Posted May 18, 2021 Report Share Posted May 18, 2021 This is a LPC rebuild I did when the Xbox was 1 day old and I still do the same today. or you could get a LPB rebuild QSB(Quick Solder Board) something like this Cheers SS Dave Soft modding is like masturbating, It gets the job done but it's nothing like the real thing. Quote Link to comment Share on other sites More sharing options...
Yanimo Posted May 24, 2021 Author Report Share Posted May 24, 2021 On 5/18/2021 at 4:24 PM, SS_Dave said: This is a LPC rebuild I did when the Xbox was 1 day old and I still do the same today. or you could get a LPB rebuild QSB(Quick Solder Board) something like this Cheers SS Dave Soft modding is like masturbating, It gets the job done but it's nothing like the real thing. did my best but still flashing orange. Quote Link to comment Share on other sites More sharing options...
Yanimo Posted May 24, 2021 Author Report Share Posted May 24, 2021 Can I give up? I don't know what to do anymore cleaned it traced it retraced it removed mod chip but still it just boots for a second then shutsdown flashing orange Quote Link to comment Share on other sites More sharing options...
SS_Dave Posted May 24, 2021 Report Share Posted May 24, 2021 53 minutes ago, Yanimo said: Can I give up? I don't know what to do anymore cleaned it traced it retraced it removed mod chip but still it just boots for a second then shutsdown flashing orange With the amount of time you have spent on it I think its time to pull the plug on it. You have a spare mod chip, PSU, GPU heat sink, Ram and a DVD drive. Cheers SS Dave Soft modding is like masturbating, It gets the job done but it's nothing like the real thing. Quote Link to comment Share on other sites More sharing options...
KaosEngineer Posted May 24, 2021 Report Share Posted May 24, 2021 Is the exhaust fan running at 100% (full speed)? Sounds to me like the console is detecting an overheating condition - possibly falsely - however, I'm not sure exactly where the temp sensor diode from the CPU connects to the custom Xyclops chip. Quote Link to comment Share on other sites More sharing options...
Yanimo Posted May 24, 2021 Author Report Share Posted May 24, 2021 11 hours ago, KaosEngineer said: Is the exhaust fan running at 100% (full speed)? Sounds to me like the console is detecting an overheating condition - possibly falsely - however, I'm not sure exactly where the temp sensor diode from the CPU connects to the custom Xyclops chip. The fan runs quietly. Quote Link to comment Share on other sites More sharing options...
Yanimo Posted May 24, 2021 Author Report Share Posted May 24, 2021 11 hours ago, SS_Dave said: With the amount of time you have spent on it I think its time to pull the plug on it. You have a spare mod chip, PSU, GPU heat sink, Ram and a DVD drive. Cheers SS Dave Soft modding is like masturbating, It gets the job done but it's nothing like the real thing. thanks dave. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.