Jump to content
Sign in to follow this  
rafa_rjdc

Hello From Brazil

Recommended Posts

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

  • Similar Content

    • By Benur75
      Hello Friends,
      I have started a new Xbox ( My wife will kill me). This time I took the time to give you some photos of my madness:
      Step1: Disassembling
      Please login or register to see this attachment.
      It was very dirty, this is a 1.1 version. I immediately removed clock capacitor (Yes a gamegear is also lying on the ground) and change thermal paste.
      Please login or register to see this attachment.
      Step2:  Hot water and soap cleaning in the kitchen on plastic parts
      Please login or register to see this attachment.
      Step3: The same for the shields
      Please login or register to see this attachment.
      Step4: Shield painting to prevent corrosion (EMI points will be paint removed after painting). This is the grey primer, after I put what I use black or white paints.
      Please login or register to see this attachment.
      Step5: And why don't adding more ram, this board is very nice. With help of my xblast lite, one chip after another.
      Please login or register to see this attachment.
      Note, that the chip N°4 gave me some problem, after test, the xbox start then stop, I check and redid the solder 3 times, after first, no boot problem on Xblast, but the chip was not anymore detected. So I decided to gently remove it, and to replace it with a new one. And it worked, I could go on with the last one.
      For people upgrading their Xbox, don't forget that a chip can fail even if it is new like for me if you realize bad solder and make a short circuit.
       
      Please login or register to see this attachment.
      As you can see, it remains some flux. It is a bit hard to remove all as I worked for a long time on chip N°4. (Near PSU connector)
      Step6: I have to confirm that everything is ok and check memory inside operating system. You can see after the last chip that XblastOS show 128 Mib.
      Please login or register to see this attachment.
      Please login or register to see this attachment.
      Inside tool menu (in settings), you can test your memory. This is what you have to do after each chip added. My prefered order is chip 2, the chip 3 ( both bottom side), then the 4th because some caps take lot of place to solder and finish by number 1.
      Please login or register to see this attachment.
      and finally check under operating system, to confirm that no blocks are failled. Some blocks can't be tested as they are used by operating system.
      Please login or register to see this attachment.
      Step7: DVD cleaning, Pot settings, new belt installation and Ide to Sata improvements.
      Please login or register to see this attachment.
      As you can see, I replace always jumper by solder ( master / slave) I had a case where the jumper falled during shippment.
      I also replace the 2 bad quality chineese capacitors bye Panasonic ones.
      Please login or register to see this attachment.
      The whole DVD case was cleaned with isopropyl alcohol, and also lens, motor.
      New greased has been applied to axles and caddy.
      DVD pot was 2400 Ohm. It is very often a too high value like this one. Samsung drives like value between 1900 and 2000 ohm.
      Look the copy  speed result after that: more than 6 Mb/s
      Please login or register to see this attachment.
      Who wants it ? I don't spoke about the Sata HDD. I will use ever a 500 Gb, or a 3tb ( I know xbox can only handle 2 Tb )
      If someone wants it and leaves in europe. I will put this box on stress test during a week and it will be ready for sale.
      It can also be delivered with original HDD ( Seagate IDE and for the future IDE2SATA adapter provided)
      If you are interrested in, send a PM.
      Bye
      Benur75
       
       
       
    • By LCRay
      I haven’t done any modding yet. I’ve got my Xbox on order, it should be in by the end of the week. I am looking forward to getting back into some original Xbox games. I pretty much haven’t touched one since the 360 came out. For now I’m just trying to make 5+ posts so I can download the repair guide! Looking forward to being part of this community. Thanks!

Board Life Status


Board startup date: April 23, 2017 12:45:48
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.