Jump to content
OGXbox.com

N64 Freaks Internal Hdmi Mod Install


N64 freak
 Share

Recommended Posts

This HDMI mod replaces the AV port completely and offers an HDMI port instead for convenience.

The Installed HDMI mod does look like this:

IMG_1689.thumb.JPG.91aac7d840c3524cd26427c9df230dad.JPG

The HDMI mod does offer 5.1 sound through the HDMI port. If you don't need 5.1 (or your TV might not support it) you can simply disable 5.1 audio and get digital stereo audio instead. For those who want to add an optical output to there Xbox the HDMI mod does offer 3 solder points to add a TOTX178 optical transmitter.

To get the HDMI mod installed you first need to get the AV-port removed.

To get it removed you could either use a hot-air station or a heat-gun to remove it at once. But that would put a lot of thermal stress on the board!
The better and recommended alternative is to disassemble the Port and remove it one part at a time.

First desolder the Metal Tab holding it in place by heating them and prying the metal tab up to pull it out.

IMG_1691.thumb.JPG.3980ce7020df29ad8d818bcba3610b62.JPG

When the metal tab is removed take a sidecutter and clip off all the pins from the video port as they are what keeps the Port in place.
When they are clipped off you can take the port cover off by simply pulling it upwards.

IMG_1692.thumb.JPG.f04eabeb7f1fb116652a5c8ad97ae8d4.JPGIMG_1693.thumb.JPG.30522786b4eaa16ee197feb2bfaa6a2a.JPG IMG_1694.thumb.JPG.6a9f3053fd217a56cd45d5f310772ee3.JPG 

Next step is to remove the remaining plastic piece and desolder the rest of the pins and clean up the area a little.

Position the first Adapter exactly as show in the photo. The red arrow marks the PTH that has to be alligned centered.

IMG_1697.thumb.JPG.f7b00c26e7f665624bf4be62e63d678d.JPG

Once Positioned solder all the marked points down and make sure they are properly connected before continuing with the second adapter!
After soldering all the necessary points insulate the 2 soler points shown in green. A piece of kapton tape works well.
You should do this to be sure there's no unwanted connection occuring between the 2 adapter pcbs.

IMG_1698.thumb.JPG.c91ab2022fdae093e4bf16541d2f1077.JPGIMG_1698_isol.JPG.573bc651b6538e13e40977ac6c52b2c1.JPG

Next up is the second adapter. Just position it above the first adapter using the 2 big holes to allign them and solder down the marked points. Again check continuity before continuing with the next PCB!

IMG_1699.thumb.JPG.704cecec5152f52a82a3ce664dacd49b.JPG

 

Last PCB is the HDMI mod itself. You need to position it slightly off centered on the second PCB. The HDMI ports pins will be position it correctly. Just solder down the points that are marked with the red arrows and the install is almos done!

IMG_1700.thumb.JPG.cbccc806ecdfd6c90e4b8ea6eba7a0b5.JPG

Last up is setting the Video mode. You need to add 2 small bridges on the bottom side of the PCB. Just solder in the 2 bridges and the video mode is set correctly!

IMG_1701.thumb.JPG.6fc4afe4ded73242be8ad85c879cd70c.JPG

If you want to use the optical out you can easily add a toslink port to the HDMI mod by simply soldering a Transmitter to the 3 marked pins.

IMG_1700.thumb.JPG.2d30228c6cecd26dee60bbc34ad78be8.JPG

Edited by N64 freak
  • Like 7
  • Thanks 1
Link to comment
Share on other sites

  • 2 weeks later...
  • 11 months later...
  • 10 months later...
On 5/14/2019 at 4:03 PM, TEK Nemesis said:

@N64 freak, you included a capacitor for the rev 1.0-1.1 boards.  Where does that go? 

@TEK NemesisDid you figure out where it goes because I got my hands on one of these chips and I cant find a install instructions for a 1.0 or 1.1 [ I am doing this on a 1.1 board with an x3]

Edited by BanXboxLiveNow
Link to comment
Share on other sites

23 hours ago, BanXboxLiveNow said:

@TEK NemesisDid you figure out where it goes because I got my hands on one of these chips and I cant find a install instructions for a 1.0 or 1.1 [ I am doing this on a 1.1 board with an x3]

Like N64 Freak say, you'll know once you try to place the PCB because it simply won't fit with that tall electrolytic capacitor there.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Unfortunately, your content contains terms that we do not allow. Please edit your content to remove the highlighted words below.
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

Board Life Status


Board startup date: April 23, 2017 12:45:48
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.