Jump to content
ironsniper1

Wii2hdmi On Xbox

Recommended Posts

hey everyone thanks to a bunch of people in discord, i managed to wire a wii2hdmi adapter to the xbox for hdmi and audio, works great and there is a difference between it and composite,

i dont have a good way to screenshot it, i tried doing a live stream on twitch but was having connection problems so it does not look to good, however if you want you can check the videos here Please login or register to see this link.  

and here is the diagrams, the one with the top of the xbox av port is if you completely desoldered the av port and are replacing the av port with the adapter and the bottom is if you are leaving the av port and just soldering in some wires to the port and adapter

Please login or register to see this attachment.

Please login or register to see this attachment.

  • Like 4

Share this post


Link to post
Share on other sites

Can you make a diagram for this based off of using the connector from a standard Xbox AV cable? I would like to perform this mod, but keep the AV port on my Xbox intact.

 

Here is a link to what I am talking about:

 

Please login or register to see this link.

 

 

 

 

Share this post


Link to post
Share on other sites

this is where i got it from also this was provided to me by Reo Au In on discord

Please login or register to see this attachment.

Edited by ironsniper1
  • Like 2

Share this post


Link to post
Share on other sites
this is where i got it from also this was provided to me by Reo Au In on discord
Please login or register to see this link.
Thank you for this! Have you performed the mod where you wire a standard Xbox AV cable connector to the Wii2HDMI board?

I really prefer the plug and play approach to that kind of mod.

Sent from my SM-G955U using Tapatalk

Share this post


Link to post
Share on other sites
Just now, XC-3730C said:

Thank you for this! Have you performed the mod where you wire a standard Xbox AV cable connector to the Wii2HDMI board?

I really prefer the plug and play approach to that kind of mod.

Sent from my SM-G955U using Tapatalk
 

nope but whoever did that diagram did

Share this post


Link to post
Share on other sites
19 minutes ago, XC-3730C said:

Yea. I was hoping someone could do it in English.

 

 By the way, the 2 diagrams for this mods look exactly the same.

 

 

 

 

they are the same just flipped one is if you have the xbox motherboard upside down so pin 1 would be on the top right and the other is if you have right side up with the heatsinks in view and pin 1 is on the left

Share this post


Link to post
Share on other sites

Thank you for the clarification! What gague wire do you reccomend using for an internal PCB mod (wired to the Xbox's AV connector) ?

 

Also, I may want to go that route, but at some point use an active HDMI to VGA converter. Is there a way to add USB port for power on that kind of adapter?

 

Sent from my SM-G955U using Tapatalk

 

 

 

 

  • Like 1

Share this post


Link to post
Share on other sites
17 minutes ago, XC-3730C said:

Thank you for the clarification! What gague wire do you reccomend using for an internal PCB mod (wired to the Xbox's AV connector) ?

 

Also, I may want to go that route, but at some point use an active HDMI to VGA converter. Is there a way to add USB port for power on that kind of adapter?

 

Sent from my SM-G955U using Tapatalk

 

 

 

 

that i do not know i dont know if you have discord or not but there is a lot of people in there who may be able to help Please login or register to see this link.  also the wire i used was Kynar Wire 30 AWG

Edited by ironsniper1

Share this post


Link to post
Share on other sites
i forgot to add that pins 11 and 13 need to be tied together and grounded
Got a picture of how that is supposed to look?

Sent from my SM-G955U using Tapatalk

Share this post


Link to post
Share on other sites

nope but it would look like this and yes i know its crappy

Please login or register to see this attachment.

 

also make sure you count the pins correct as you go so you know you are soldering to the right one

Edited by ironsniper1
  • Like 1

Share this post


Link to post
Share on other sites
Just now, XC-3730C said:

That is amazing! Are you gonna try to fit the connector and wiring back into the Wii2HDMI shell?

no i broke it opening it so i am not worried about stuffing it back in, all though that being said i wish i had a 3d printer i would 3d print a custom case

Share this post


Link to post
Share on other sites
1 minute ago, TEK Nemesis said:

It's possible to cut an opening in the case for the Xbox connection.  (This is not my photo.  I found it floating on the net.)

 

Please login or register to see this link.

i know but i would rather have something cleaner, like say with some of the original cable still attached, think of it kinda of like a laptop power supply i just think it would nicer

Share this post


Link to post
Share on other sites
2 minutes ago, ironsniper1 said:

i know but i would rather have something cleaner, like say with some of the original cable still attached, think of it kinda of like a laptop power supply i just think it would nicer

I don't know if this is a good idea unless you are using a very high quality shielded cable in your mod (which would kind of be a huge waste, like converting a Lamborghini into an ATV).  Normally people are doing this mod with a cheap unshielded cable or an OEM MS cable with just the three connections (yellow, red, white).  If you are not using a high quality shielded cable then the mod may not produce the best results.

Share this post


Link to post
Share on other sites
24 minutes ago, TEK Nemesis said:

I don't know if this is a good idea unless you are using a very high quality shielded cable in your mod (which would kind of be a huge waste, like converting a Lamborghini into an ATV).  Normally people are doing this mod with a cheap unshielded cable or an OEM MS cable with just the three connections (yellow, red, white).  If you are not using a high quality shielded cable then the mod may not produce the best results.

i didnt say anything about the cable i was describing how i would want the whole thing to look

Share this post


Link to post
Share on other sites
5 hours ago, ironsniper1 said:

i would rather have something cleaner, like say with some of the original cable still attached

You didn't say anything about the cable but you want some of the original cable still attached?  I'm confused.

Share this post


Link to post
Share on other sites

I have posted this over a year ago in the tutorial submission section,  it fits inside the wii2hdmi case cleanly,  the picture you used is only as a markup where to cut. 

  • Like 1

Share this post


Link to post
Share on other sites

Btw just out of curiosity, I read in the other thread on GBAtemp that there is also an upscaling version. I also have a Wii and I already have a black one of these adapters (which will probably also look better for the Xbox) but this one has auto upscaling. Does one of you guys know whats the difference and which one to buy?

I have this one myself: Please login or register to see this link.

And this one with the "hole" should be a version with manual upscaling through a needle Please login or register to see this link.

Thanks for the tutorial, can't wait tot try it out :D

  • Like 1

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Content

    • By Xbmcmodsforxbox
      Xecuter 2.6 ce motherboard v1.6 and 80gb ide all wires and 1 official controller 100 usd shipped us only
       
      Please login or register to see this attachment.
      Please login or register to see this attachment.
    • By sidocious
      Hi, it's me again with another weird problem
      So, my friend gave me another Xbox with the following issue.
      When I plug in the power cable into the Xbox, the fan speed jump for about 4x highest than the normal (why it is turn on???). When I power up the Xbox, that is goes to normal speed. If I turn it off, than the speed jump to high speed again...
      There is no any corrosion and the capacitors in good condition... 
      The Xbox is in original state. There is no modchip or softmod or TSOP flash.
      Thanks for your help!
    • By sidocious
      Hi Mates,
      I met the following issue, I try to explain everything... I'm totally lost in space, so I hope, you have some idea what happening...
      So, first, what you have to know:
      - I've got an xbox classic v1.6 without video and sound output.
      - When opened it, I found a MuppetX modchip in it. My friend inform me, he try to flash this modchip, but 1MB always gave an error message "mismatch bios size", so he flashed it with 256KB bios. That was the mistake of him, so the modchip never works again... (The LPC Chip is 49LF020A, like in Aladdin)
      - I flashed it with USB Programmer with many types of bios.bin, tried 256, 512, 1024 evom8+ for v1.6, I tried everything to use it again... But the only working solution was to flash it with 4*256kb = 1MB XBlast OS bios. But when I use XBlast NET bios flasher (cause I can't use any other way, just USB programmer), the flashed bios never works.
      - I checked all capacitors and all of them is in good conditon... I checked traces and all of them in good condition.
      - When I push (more than 5 sec) the power button, the xbox started and loaded the XBlast OS. Without modchip (power up with eject or just push power button) there is no video or sound output. If I change the Bank (I do not know is it bank0 or bank1), the Xbox turn off and turn on again...
      My questions:
      - Is there anyone who has an original dump of a MuppetX bios?
      - Which is the Bank0 and Bank1 on MuppetX?
      - Which BIOS size the correct for that? (As I said, I try 1MB first and all other sizes, but won't work...)
      - Why Xbox doesn't give video and sound output without modchip?
      Is it maybe an EEPROM error?...
      Thank you in advance!
      BR, Zsolt
      ps: I red this topic: 
       but do not help

Board Life Status


Board startup date: April 23, 2017 12:45:48
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.