Search the Community

Took me 2 days to get all the wiring right. for the wii2hdmi for og xbox modd ... using a wii2hdmi device ordered off eBay you can also find an Alibaba and other places like this. Very inexpensive around 5 Canadian dollars. You're also going to need some sort of a donor Xbox RCA wires or component wires in order to pull this off. There is 11 connections total five of which are ground I do not suggest not adding all the ground cuz could cause interference. Had pretty good luck I made to both of them are crystal clear with no interference. I tested on version 1.0 as well as version 1.4 turned out very good. I tried to look up and down online for some sort of schematic nothing appeared. There was one picture that was in Spanish but it was misleading I tried to look into it to find out who the original inventor was found the person at XB Classics a Brazilian site. After conversating with him he told me that he had better pictures but he would not share. Then I noticed a site that they has linked where they were selling these to the equivalent of 40 US dollars a piece so that is the reason the images that they uploaded are just there to confuse people. So that they cannot make it. Does not include audio left or right. And apparently La stands for 5 V? Don't ask me but that's what the guy told me makes no sense at all. I spent two days getting the wiring correct. I documented everything and put it on a YouTube video (link2come) was trying to figure out the best way to make this readily available for everybody in the world any Xbox Enthusiast should have a low cost HDMI adapter solution available to them this is where these schematics come in. Again I didn't notice any interference at all. Just a little bit in the Bios when only running 480 but there's not much you can do unless you re Flash the BIOS to force. I've noticed people in the group posting pictures not even having soldering skills and getting very good results from this method. In theory you can use this exact same adapter in order to have an internal HDMI solution. These images are water marked because these are going to be the only good images that are online and I seen the way XB classic does their water mark and it really bugs me that they did that so I wanted to make sure that everyone knows where it came from. That being said I'm Mister James Reid really helped me out with this he volunteered his services in order to take my hard copy drawings that were on paper and make it look something presentable. Which he did and he did a great job thank you very much James I did in fact alter the images to have the watermark across them. Sorry about that but I figured since I put in the work I deserve to have my name on it. If you have any questions please do not hesitate I do not check this site every day but I do come in from time to time. Thanks again and I hope people online can use this receive money from the big corporations like pounds and hyperkin charging ridiculous amounts of money for something so cheap... I've also got a lot of questions recently about people asking if this is any better than component. It uses the component wires in order to transfer the signal into HDMI. I'm not too technical with that end but when looking up the chip number on the actual board for the Wii to HDMI adapter I did notice in there schematics and their breakdown for the actual board they did mention that the video board that does the decoding actually does video on hand splint what kind of video enhancement I have no idea. But it should be an enhancement over component if they are speaking the truth. Anyway gentleman without further delay here are the schematics. I hope this hope somebody somewhere. Thank you very much Frank

I started working on an alternative to the HD AV pack but with added SPDIF RCA, as well as an internally mountable version with a 3d printed panel to snap or screw into the outer case if anyone would be interested in that. I liked the XOSVP's use of a VGA connector so I've included that and I see most designs with YPbPr output using 75ohm resistors, but are these actually necessary if my traces are wide enough to have an impedance of 75 ohms and will they make a difference on the L/R analog audio connections? I've only started learning this stuff recently so I'd like to know if anything about the schematic is no good. I'll post the design and editable PCB once I have it finalized. Integrally mounted version with DPDT switch to enable av mode 2+3: based on this diagram:

have some weird Power issues, researched previous posts but didn't want to hijack their threads and not sure if they were the same situation anyway. Here's the current situation: Bought console off ebay with acknowledgement that power button did not work and that it powered on by simply plugging in or hitting the eject button...(sounds like classic trace rot). Clock cap was removed by seller and area cleaned, he also replaced thermal paste on CPU/GPU and verified that the console worked and played games. I have not verified trace damage extent yet but he said there was a little. The console appears to have other things going on other than trace rot and I wanted to see if there was something else I could test on the top of the mb based on the below current working status before I get to trace rot stuff. When I got it, after a couple of power cycles where it remained powered on plugging it in, it now no longer powers on simply by plugging in, instead it only does by hitting eject button, and when that occurs it only stays powered on for about a second. Stby voltage checks good at 3.3V and POWON just gets to 3.3V before it powers off. POWOK doesn't fully spool up. When DVD removed and only HD power still attached (or even if HD removed), it powers on via eject button for 6 seconds and provides the following readings: Eject button triggers POWON voltage at 3.3V for 6 seconds. POWOK registers at 3.3V as well until it cuts off. Even if button remains held down, voltage drops off on both at 6 seconds and it powers down All other voltages read correct during the 6 sec power on except the yellow which comes in at 11.8vdc Eject button LED comes on and flashes red. If DVD plugged in, when eject button pressed DVD is ejected and retracts before powering down No obvious Cap leakages/bulges discovered. Any ideas? Thank you!

i tried soldering in a pin header for an alladin modchip. the modchip didn't work so i need a schematic to see which part of the board each pin is suppose to connect to so that i can check my work with an ohm meter. anyone have that schematic? it's a version 1.0.