Jump to content
OGXbox.com

Search the Community

Showing results for tags 'fried'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Rules
    • Why Can't I Download?
  • Subscribed Members Only
    • Subscribed Members Only
  • Off Topic
    • New Member Introductions
    • Rumble Pit
    • Suggestion Box.
  • General Xbox Discussion
    • General Xbox Discussion
  • Original Xbox Modding Forum
    • Hardware Mods
    • Modchips
    • TSOP Flashing
    • Softmods
    • Repair
  • Xbox Case Modding
    • Case Mods
    • Lighting & Electrical Mods
  • Tutorials
    • Official Tutorials
    • Tutorial Submission
  • Software
    • Bios
    • Dashboards
    • Installation Disks
    • Applications
    • Games
    • Emulators
    • Homebrew
  • Xbox Collecting
    • Xbox Collection Showcase
  • Rare and Uncommon
    • Rare and Uncommon Xbox Hardware
    • Rare and Uncommon Xbox Software
  • Vendors
    • N64 Freak's Products
    • Barnito's Products
  • Development
    • Rocky5's Projects
  • Online Play
    • Game Night
  • Classifieds
    • Wanted
    • For Sale
  • Moderator Section
    • Moderator Back Room

Product Groups

  • Vendor Forum
  • Membership Subscriptions
  • Forum Ads

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


About Me

Found 3 results

  1. Got a dead XBOX 1.6 for cheap, it was super clean but had been previously opened so I was a little wary of what I'd find inside. Power supply fuse was missing and the attached pic is the soldering butcher job i found. I'm not familiar with 1.6 PSUs, and couldn't find any quality pics of one online to see what the layout is supposed to be, so i'm wondering if there is any saving this? Don't know what continuity (if any) is supposed to exist between the 3 points there. The bottom round hole is where the fuse is supposed to attach. Worried that the damage/solder spill shorted or created unwanted continuity but can't tell since I don't know how it was originally. The brown lines are what appears to be scratches as if someone tried to scratch away solder to keep the points separated? I dunno. If it is fixable, was wondering what could have caused the fuse to blow that necessitated the repair attempt, as in are there any usual suspects I should look/test for on the Power supply? The rest of the Power supply looks fine. The mobo had some bad caps so i went ahead and replaced the 5 usual ones there but other than that no visible defects on either the mobo or power supply. Any help or thoughts on power supply layout and downstream test/checks would be greatly appreciated. Thanks!
  2. harrytooth

    Fried Psu

    Hey guys, I'm an American that has lived in Europe for 10+ years. When I initially came over, I brought along my original xbox console and had a lot of fun with it until I made the mistake of plugging the 110v system into a 220v outlet without a transformer... Dumb, I know but now I want to fix it. This console is a circa 2004 Halo Edition so it would be a real shame to toss it. I received a used PSU from Ebay (a Foxlink) and modified the plug in order for it to work following a great article from this forum : Thanks Xbox Admin, this article was really helpful. I unfortunately couldn't get the console to power on even though everything was hooked up. So my question is, does anyone know if the there's a possibility that I managed to damage the whole console beyond repair? Should I pull the trigger on another (and correct Delta PSU this time) to try fixing it again? If anyone has any advice I would love to hear it. Thanks!
  3. hey guys, tried to use M7 recovery BIOS on one of my systems when I guess I decided to get a little too creative and attempt the pin header install. Improvising a pin header out of a busted IDE drive went great, but I guess I installed the chip backwards. Xbox doesn't show any issues besides the obvious bad flash, but either 10-wire or pin header installs result in a straight FRAG (three reboots and all) as soon as D0 is grounded. I tried going through the chip and just tying D0 to one of the pads on the board. My Aladdin gets here on Monday, but is there any known fix here? My guess is supplying 5v instead of 3v over one of the pins gave it a pretty good zap and that's that. Thought it was worth asking about since I don't have aJTAG programmer to upgrade the Aladdin, though.

Board Life Status


Board startup date: April 23, 2017 12:45:48
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.