Jump to content
OGXbox.com

Search the Community

Showing results for tags 'displaying'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Rules
    • Why Can't I Download?
  • Subscribed Members Only
    • Subscribed Members Only
  • Off Topic
    • New Member Introductions
    • Rumble Pit
    • Suggestion Box.
  • General Xbox Discussion
    • General Xbox Discussion
  • Original Xbox Modding Forum
    • Hardware Mods
    • Modchips
    • TSOP Flashing
    • Softmods
    • Repair
  • Xbox Case Modding
    • Case Mods
    • Lighting & Electrical Mods
  • Tutorials
    • Official Tutorials
    • Tutorial Submission
  • Software
    • Bios
    • Dashboards
    • Installation Disks
    • Applications
    • Games
    • Emulators
    • Homebrew
  • Xbox Collecting
    • Xbox Collection Showcase
  • Rare and Uncommon
    • Rare and Uncommon Xbox Hardware
    • Rare and Uncommon Xbox Software
  • Vendors
    • N64 Freak's Products
    • Barnito's Products
  • Development
    • Rocky5's Projects
  • Online Play
    • Game Night
  • Classifieds
    • Wanted
    • For Sale
  • Moderator Section
    • Moderator Back Room

Product Groups

  • Vendor Forum
  • Membership Subscriptions
  • Forum Ads

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


About Me

Found 3 results

  1. Hello All, I recently put a Seagate 3TB HDD in an original xbox Rev. 1.6 with Xecuter 2.6 modchip. I split the F and G drives evenly and everything installed and worked fine. I just tried the same with an identical hard drive in a xbox Rev. 1.4 with Xecuter 3 CE modchip (X3 3294 Bios) and the G-drive size doesn't display correctly. I used TruHeXEn 2021 DVD-R to format the new drive. I then used XB Partitioner on that same DVD-R to format the F and G again. I pressed "A" until the F and G were even and made sure they were 64k clusters. Formats in XB Partitioner fine and then when I check the hard disk settings while still in TruHeXEn, they both display and show the same expected size. But when I eject the DVD-R and boot off the HDD and check hard disks in dashboards, the G-Drive shows as 0MB and sometimes doesn't display at all. The F works fine though. I tried formating them @ 10 times, same thing. If I FTP in, the F-Drive shows and is writable, but the G-Drive doesn't even display as an option. Any ideas why the G-Drive is not displaying the correct size? Thank you!!!
  2. I've done the softmod with rocky5 and changed to NTSC in nk patcher and everythings good with componant cable picture wise in dashboard. I've tried launching tiger woods 2004 pal game via disc and just get blank screen ? is there a specific setup in the video options to get pal games to work once you change to NTSC ?
  3. Thought I would ask this question here as I ran into this the other night while using a few consoles as guinea pigs for testing a few things. I've been familiarizing myself with the process of cloning drives using Chimp 261812 and have successfully done two with no issues - one on a softmodded console and the other on a hardmodded console. However I noticed Chimp 261812 on Rocky5's Extras Disc works perfectly fine with my component cables. Chimp 261812 on HeXEn (specifically 2018 when I tried it) would cut to black and not display anything on my setup after I pressed "A" after hooking up the slave hard drive. I restarted the process on the HeXEn build using composite cables as opposed to component and had no issues. Is this common? Has anyone tested Chimp 261812 over component cables with 480p/720p/1080i disabled as well? I was going to do that last night but forgot about it.

Board Life Status


Board startup date: April 23, 2017 12:45:48
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.