Search the Community

Hi, I have put this on the Facebook group also. I have an X2.6 chip in an old v1.0 Xbox and I was going to pull it out and put it in a different one however the PCB with the bank switches has gone missing. No idea where it is. What are my options? Ideally would like to have the full functionality and flash it again. Anyone have the switch PCB and want to part with it has anyone done their own switches for it? The ribbon cable to the non existent switch PCB is intact.

Evening all i've got 2 2.3b Lites and one 2.6. Anybody got the install diagrams as I can't seem to find them only the 2.3b+. Also with my LPC Rebuild kit they should work for 1.6's as long as I flash a working bios / Cromwell before installing? As I've ran out of Aladdins and have a few consoles in need of work.

Hi all, Does anyone know what the latest bios version release is for the Xecuter 3 CE modchip is? I have a v1.6 of the Xbox.

Is there any way to see what bios are flashed without going through all of the switch combos?

What you see is what you get, brand new in package X3CE Xecuter 3 Kit. Accepting offers.

Xecuter 2.6 ce motherboard v1.6 and 80gb ide all wires and 1 official controller 100 usd shipped us only

Hi everyone. What Xecuter MOD Chip is this? I tried browsing the stickies but couldn't find a matching picture. The only thing I remember is that this was solderless. Also, is there a diagram somewhere that I can solder it into the XBOX instead? Thanks in advance.

Hey guys please contact me if you have any old original xbox mod chips that you would be willing to sell i may be intrested in some xenium chips and smartxx but just contact me if you do thanks

140 shipped both work fine no issues

Selling x3 chips and xlcd brand new mod chips are used

Re-listed due to time waster. https://www.ebay.co.uk/itm/Xecuter-3-CE-Modchip/223547347458?hash=item340c75d202:g:8hwAAOSwCLxc8~oE

Hello everyone and thank you for taking the time to read my post,requesting urgent help with regards my.Xecuter X2.6CE modchip. As you can see in the photo i've uploaded.The red 5v socket is damaged (it was like this when i was given the chip,many years ago with the front switch board and chip to switch board cable BUT their wasn't the red 5v wire included).The socket's plastic has been damaged and it's missing it's 2 tiny pins.The 2 solder pads are still there though and i have tried soldering on a peice of wire to go from the solder pad on the chip to the 5v point on my V1.6 Xbox. No luck what so ever,even though i have tried the wire on both pads (one by one and not bridged together of course) When i power up my console,it will quickly power on then switch off,then again quickly switch on,then switch off.It does this 3 times then it'll stay on with a black screen and the front RF boards LED's flashing from red to green,red to green (Fragging i think it's known as) Please can anyone help me as to where i need to solder the piece of wire on the chip so i can use the chip in my V1.6 Xbox ? Thanks so much guys,any help from you would be truely apprieciated indeed.

https://www.ebay.co.uk/itm/Xecuter-3-CE-Modchip/223538636713?hash=item340bf0e7a9:g:8hwAAOSwCLxc8~oE

Hellow OG Xbox community, creating this topic as a place to discuss installation, operation and modding of an Xecuter 3 CE Red-backed modchip with LCD, for help and questions, I am in no way an expert, but a very knowledgeable technician who is interested in helping others to use, repair or mod their systems. Lets share knowledge!!

Hi, I upgraded my xbox to a 1TB sata drive but I can only see 123gb. I understand I need to update the bios on the modchip I have which I believe is an Xecuter 2.3 lite. I tried using Hexen to upgrade to x2.4981 but I get the message !!Flash Not Writeable!! This happens if I have the switch set to protect or unprotect, Bank 1 or Bank 2. I downloaded a copy of x2.5035 so I could go with that version outside of Hexen, but I don't know how to do that. Please could someone assist me. Thank you.

Ok guys got an issue that is getting on my wick. Slapped a 2.3b Lite into a 1.6, used a clone LPC Rebuild Kit and proceeded to boot the console. D0 was connected to the board and ground was connected to the screw hole as usual. As soon as you put power to the console it will boot up then reset 2 times before FRAGGING. Only when D0 is connected and chip is off. With chip on with M8 1.6 Bios I can get a boot with Evo shield but it hangs after that and still turns on as soon as a power cord is plugged in. Front panel doesn't work at all. Remove the chip or D0, and it'll boot fine to the original softmod it came from. I've reworked it with my iron, even given it a hot air rework. Which point is most likely the culprit? Apologies on the lead free solder. Was using a friends over my own.

Hi guys I have an xbox with xecuter 3 and pro switch.. If anyone would like to make an offer

Hi, I've got an xecuter X3IR installed and its all working but I have got a problem I cant seem to figure out? When X3IR is enabled the light around the power button changes colour, one side is red and one side is green? How do I get it to go back to just be green? Ive connect it up to X3 IR manager but there isn't a setting for changing the power button LED colour or am I missing something? Or is this just a feature to tell you X3IR is enabled? If I unplug the X3IR the light goes back to green both sides so it defiantly something to do with the X3IR. Any help would be much appriciated Cheers

EDIT: Never mind the chip wire on the bank came loss . lol All sorted

Selling on ebay to make it fair on UK buyers. I really want this to go to a good home, I am only selling as I am moving house and need the money towards fees otherwise I would have kept it eternally haha. Thanks for taking the time to look. https://www.ebay.co.uk/itm/Very-Rare-Team-Xecuter-Original-Xbox-With-TX-Faceplate-128mb-Ram-X3ce-Xapt3r/113716250636

Hi guys hope it helps those who have a broken/missing usb ports on the x3cp v1.0 needed a few minor dimensional changes to fit snugly in the stock x3cp usb board slide slots i had to shave off 1-2mm from the sides of the pcb for it to seat properly and not damage the housing. these files are v1.1 and the required changes have been made i recommend 1.00mm-1.6mm board thickness any questions feel free to ask https://mega.nz/#!LkNAFYSJ!SDPPguhC64fcmEvT2RkIuT_xdSYkedqKGIfJJlUAJQA

This may sound weird and maybe it is but can I softmod or better should I softmod with the xecuter hardmod installed? I heard modern softmods are better.

Custom Red LED controller Ports with matching Red LED Power/Eject Board. Comes with lifetime warranty. If one ever fails I will replace it for free minus the shipping cost. These are very bright and match 100% although the picture kinda takes away from how deep red these really are. $24.99 Shipped anywhere in the lower 48. Can ship worldwide. Other colors available: Blue, Green, White, Purple, Orange, Red Any questions, simply shoot me a message! Thanks guys!

A friend gave me back the xbox I made for him years ago. I want to update it for my grankids. It is chipped with an xecuter 2, is a version 1.6, and currently has an ancient 150GB hdd. Primarily, I want to put in a new HDD, planning on a 500GB, and use a Startech SATA/IDE adapter with an 80 wire cable. Then I want to add Coinops, and XBMC; the XBMC primarily for karaoke. Also a decent dash, thinking probably the last UnleashX. I have copied all the contents onto a drive via ftp. I am confused as to how to 1) install the new hdd and 2) how to install the dash/apps. From what I read on the wiki and elsewhere, supposedly, I can just install the drive, boot, and the xecuter wizard should walk me through formatting the drive. I assume that then I can put in the Hexen disk and it will install the dash's. Is this right? My xbox modding days are long behind me (even the 360 mod days, lol). Any help is appreciated.

Is anyone interested in helping us modders out I contacted xecuter about the xecuter 3 mod chip and they said they could sell the mod chip again if somone wanted to buy 5,000 or more mod chips they said the project would cost 30,000 dollars at least but at least we know we can still get them if anyone would want to help out on this project just send a message to me.