Jump to content
OGXbox.com

Search the Community

Showing results for tags 'pinout'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Rules
    • Why Can't I Download?
  • Subscribed Members Only
    • Subscribed Members Only
  • Off Topic
    • New Member Introductions
    • Rumble Pit
    • Suggestion Box.
  • General Xbox Discussion
    • General Xbox Discussion
  • Original Xbox Modding Forum
    • Hardware Mods
    • Modchips
    • TSOP Flashing
    • Softmods
    • Repair
  • Xbox Case Modding
    • Case Mods
    • Lighting & Electrical Mods
  • Tutorials
    • Official Tutorials
    • Tutorial Submission
  • Software
    • Bios
    • Dashboards
    • Installation Disks
    • Applications
    • Games
    • Emulators
    • Homebrew
  • Xbox Collecting
    • Xbox Collection Showcase
  • Rare and Uncommon
    • Rare and Uncommon Xbox Hardware
    • Rare and Uncommon Xbox Software
  • Vendors
    • N64 Freak's Products
    • Barnito's Products
  • Development
    • Rocky5's Projects
  • Online Play
    • Game Night
  • Classifieds
    • Wanted
    • For Sale
  • Moderator Section
    • Moderator Back Room

Product Groups

  • Vendor Forum
  • Membership Subscriptions
  • Forum Ads

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


About Me

Found 5 results

  1. So I have an executer 3ce chip that is missing the reset/eject adaptor. I have the cable that connects To the chip I just need to know which wires, that are connected to the eject/reset buttons on the Xbox, to splice into. Any help would be appreciated. Thanks!
  2. have some weird Power issues, researched previous posts but didn't want to hijack their threads and not sure if they were the same situation anyway. Here's the current situation: Bought console off ebay with acknowledgement that power button did not work and that it powered on by simply plugging in or hitting the eject button...(sounds like classic trace rot). Clock cap was removed by seller and area cleaned, he also replaced thermal paste on CPU/GPU and verified that the console worked and played games. I have not verified trace damage extent yet but he said there was a little. The console appears to have other things going on other than trace rot and I wanted to see if there was something else I could test on the top of the mb based on the below current working status before I get to trace rot stuff. When I got it, after a couple of power cycles where it remained powered on plugging it in, it now no longer powers on simply by plugging in, instead it only does by hitting eject button, and when that occurs it only stays powered on for about a second. Stby voltage checks good at 3.3V and POWON just gets to 3.3V before it powers off. POWOK doesn't fully spool up. When DVD removed and only HD power still attached (or even if HD removed), it powers on via eject button for 6 seconds and provides the following readings: Eject button triggers POWON voltage at 3.3V for 6 seconds. POWOK registers at 3.3V as well until it cuts off. Even if button remains held down, voltage drops off on both at 6 seconds and it powers down All other voltages read correct during the 6 sec power on except the yellow which comes in at 11.8vdc Eject button LED comes on and flashes red. If DVD plugged in, when eject button pressed DVD is ejected and retracts before powering down No obvious Cap leakages/bulges discovered. Any ideas? Thank you!
  3. Alright folks, Of the numerous aladdin chips i've installed into 1.6 xboxes, i have installed the pin header with pin 4 removed, rebuilt lpc, connected bt->gnd on chip, cut the lframe trace at the xyclops chip and ignored installing the d0->gnd wire. This has always worked fine for me. Recently i have seen different and conflicting instructions on de-pinning the header. it was suggested to also remove pin 3 (lframe), 6 (5v) and 12 (gnd). I'm wondering what the benefit is and whether i need to start doing it this way? I'm presuming pin 6 has been left out so standby power isn't lighting the led, and pin 3 to disable lframe without cutting the trace? why remove the second gnd (pin 12) though? Just wondering what the consensus was on this, is this a better way to do it, is my usual way now incorrect?? Figured it was time to ask the experts! Cheers

Board Life Status


Board startup date: April 23, 2017 12:45:48
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.